2gig Technologies 2GIG-NTRL2, Инструкции по установке и программированию

Страница: 18 / 52

16
Each system installed will require programming. Most installations
being performed by the professional alarm installer for a specifi c
organization will have common values set in every Control Panel
reporting to the same Central Station. Other programming values,
such as the account number and sensor setup, will be unique for
each installation.
Following is an outline to guide the professional alarm installer
through the programming of the Control Panel.
If you don’t read anything else, read this outline!
Use the following outline in conjunction with this copy of the
Installation and Programming Instructions to guide you through
the installation.
Because of the many programming options available with this
Control Panel, thoroughly reading this manual is very important.
Understanding the Control Panel’s programming structure will help
to save time during each installation.
At this stage, all the wireless and hardwired sensors should be
installed, and the Control Panel should be mounted, connected,
and powered-up.
1. Start at the Home Screen.
2. Press the logo at the lower right corner of the screen.
(The Installer Toolbox can also be accessed via
the third screen of the System Toolbox.)
3. Enter the Installer Code (default = 1561) to display the Installer Toolbox.
4. Press SYSTEM CONFI G URATION and begin
programming as described on Page 18.
5. USE THE INSTALLATION LO G SHEET TO RECORD
PRO G RAMMED VALUES FOR THE SYSTEM.
6. After setting all the required programming values for the sensors and
the Control Panel, press
END , then EXIT , to save the changes.
7. After the Control Panel restarts, press SECURITY , MENU ,
TOOL B OX , enter the Master User Code (default = 1111), press
USER MANA G EMENT and setup the user’s codes. Be sure to
set a Duress Code as User #8. Press B ACK when fi nished.
8. Press B RI G HTNESS / VOLUME and set the levels for the installation.
The volume setting DOES NOT affect the volume of alarm sounds.
9. Press
➜
to view the second toolbox screen.
10. Press B ACKLI G HT TIMEOUT and set the display lighting timeout.
11. Press SET DATE and SET TIME and set the calendar and clock. (If the
GSM module is installed, the date and time are set automatically.)
12. Press the button to return to the Home Screen.
After all setup and programming, refer to the Operation and
User’s Guide for details on operating the system.
Check off the
programmed options for the system in the User’s Guide.
Be sure to instruct the subscriber on the proper operation of the
system, and leave the User’s Guide at the installation site for
reference.
SIA CP-01 Defaults
Several system programmable options have the defaults pre-set to
provide compliance with the Security Industry Association CP-01
Standard. All other system settings and functions that are required
to comply with SIA CP-01 are permanently programmed into
the Console and cannot be changed. Refer to the table for each
programmable option that has a required SIA CP-01 programming
default.
Programming Outline
Figure 47. Installer Toolbox Screen
Figure 48. System Confi guration Question “Q-1”
PRO G RAMMIN G QUESTION SIA CP-01 DEFAULT RAN G E
Q-1 Wireless Sensor Dialer Delay 30 Seconds On or Off
Q-2 Wired Sensor Dialer Delay 30 Seconds On or Off
Q-5 Exit Delay 60 Seconds 45-120 Seconds
Q-6 Entry Delay #1 30 Seconds 30-240 Seconds
Q-7 Entry Delay #2 45 Seconds 30-240 Seconds
Q-10 Call Waiting Disable Code No Default Code 0-6 Digits
Q-20 Swinger Shutdown Count 2 Trips 1-6 Trips
Q-26 Auto Stay Enabled Enabled or Disabled
Q-27 Exit Delay Restart Enabled Enabled or Disabled
Q-31 Cancel Time 5 Minutes 6-254 Minutes
Q-32 Cancel Display Enabled Enabled or Disabled
Q-35 Abort Window Dialer Delay 30 Seconds 15 or 45 Seconds
Q-78 Select Output Follows Internal Sounder See Q-78 for Options
Figure 45. The Home Screen
P r e ss lo g o to a cce ss
the I ns t a lle r Tool b ox
Figure 46. Toolbox Screen Three
I ns t a lle r Tool b ox c an b e
a cce ss e d he r e a l s o