www.1byone.com
www.1byone.com
www.1byone.com
Fuse Replacement
If the Fog Machine does not work at all when it is connected to the power socket, then it is probably
that the fuse has been broken.
WARNING:
Risk of electric shock and fire. Disconnect from power socket before replacing the fuse.
1. Turn the fuse knob counterclockwise to reveal the fuse.
2. Replace the fuse with the same size and type fuse: 5A, 125V
3. Place fuse in cover and reinstall by turning clockwise. Be sure not to over tighten.
Cautions and Warnings
●
Please read through this instructions manual before use.
●
Before use, check the fog machine to see if there is any crack in the product cover, wired control
cable and box, power cable and plug. Make sure there is not any exposed wired. Do not use if any
of the above conditions is found.
●
The fog machine will become hot during use. After use, please wait for some minutes before trying
to touch it by hand.
●
Keep away from the spray nozzle at least 0.5 meters when the nozzle spraying fog.
●
Attention! Do not place the product onto wet or uneven surfaces. Accidental falls may cause fire.
●
The product shall be changed if it has become damaged or thermally deformed. Disconnect this
product from power immediately in case of malfunction. Do not resume use until it’s repaired.
●
Do not use outdoors. It is not waterproof.
●
This product is not a toy. Please keep this unit out of reach of children and pets.
●
Close supervision is necessary when this product is used by invalids, or disabled persons, or near
children.
●
Use this product only for its intended use as described in these instructions. Do not use
attachments not recommended by the manufacturer.
●
Keep the power cable away from heated surfaces.
●
Never drop or insert any object into any opening.
●
Please unplug the power cable if you want to stop use of this unit for long time.
●
The external flexible cable of this product cannot be replaced; if the power cable is damaged, the
product shall be destroyed. Never operate this product if it has a damaged cable or plug, if it is not
working properly, if it has been dropped or damaged, or dropped into water.
WEEE Directive & Product Disposal
2
3
4
Names for Parts
How to Use?
Before using the fog machine, you have to prepare Fog Liquid (not included). Then operate
according to following sequence.
1. Remove all the packages.
2. Carefully put this product onto a clean, flat and solid surface, close to the power socket.
3. Unscrew the lid on the tank by turning counterclockwise and pour the Fog Liquid inside. Do not
spill Fog Liquid onto the product body. Do not overfill. If liquid gets into the Fog Machine, leave it
to be dry completely before plugging in. Do not cut, pinch, or break the tube connected through
the tank lid. Screw the lid clockwise to the tank tightly. Always make sure there is enough Fog
Liquid in the tank before using the Fog Machine.
4. Connect the wired control cable to the Interface at the back of the Fog Machine.
5. Connect the product with proper power socket.
6. Warm up time is approximately 4 – 5 minutes. When fully heated, the Wired Control Indication
Light will turn on and the Fog Machine will be ready to produce and spray fog.
7. Set the On/Off Switch to on position, nozzle will start spraying fog. Set to off position, spraying
will stop.
8. Turn off the unit before refilling the fog machine.
9. Unplug the unit when not in use.
10. To refill the tank; turn off the unit, unplug and follow the directions in Step 3.
11. For Indoor Use Only.
Additional Information
(a) It is normal if there is condensation on the nozzle of the Fog Machine.
(b) A small amount of fog may spray during or after operation.
(c) The Fog Machine will have to reheat after long spray. It will stop operation for a short period in
order to heat up to operating temperature again. While this is happening, fog cannot be
produced. The Wired Control Indication Light will turn on again when the unit is ready to
generate more fog.
(d) All fog machines are apt to clogging due to the consistency of Fog Liquid and the high
temperatures at which it vaporizes.
Maintenance and Cleaning
●
Maintenance and cleaning shall only be done to the product surface. Unplug this product from
the power socket before cleaning.
●
Do not wet any electric parts of this product. Please use a dry, soft cloth instead of sharp tools for
cleaning.
●
If you find there is low fog output after many hours of continuous operation or after the machine
has been idle or in storage for a long time, it is advised to empty all Fog Liquid from the machine
and clean the tank. Please unplug the machine from power socket before cleaning.
Storage
It is important to clean up fluid in the Fog Machine when storing for an extended period of time.
1. Remove the tank lid. Pour out the fog liquid in the fog machine to a container.
2. Keep the fog machine working for a few seconds to run out the fog liquid in the fog machine.
3. Fill a little fog machine cleaner liquid in the tank, keep the fog machine working till running out.
4. Switch off, unplug the fog machine, and put it on a flat, dry place.
(A) Spray Nozzle (B) Handle
(C) Tank Lid (D) Product Cover
(E) Wired Control Cable Interface (F) Fuse Knob
(G) On/Off Switch
(H) Wired Control Indication Light
(I) Wired Control Box
(J) Wired Control Cable
A
B
C
E
J
H
G
I
F
D
A: Fog Machine
B: Wired Control Box and Cable
C: Fog Liquid (not included)
D: Power Cable
At the end of its serviceable life, this product should not be treated as household or
general waste. It should be handed over to the applicable collection point for the
recycling of electrical and electronic equipment.
