Eaton Magnum MR2 Скачать руководство пользователя | Manualshive

Страница: 1 / 12

background image

Instructions for installation, operation,

and maintenance of Magnum MR2

(integral racking)

Contents

Description Page

Notices and warnings . . . . . . . . . . . . . . . . . . . . . . 2

Eaton contact information . . . . . . . . . . . . . . . . . 2

Motorized remote racking (MR2) .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Secondary connectors  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 3
Permissive interlocks  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 4

Operational interlock features . . . . . . . . . . . . . . 4
Restricting operation . . . . . . . . . . . . . . . . . . . . . 4

Manual racking    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Racking indication   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 5
Setting the breaker type   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Setting the Modbus address   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 6
Control options    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7

Option 1   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7
Option 2   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7
Option 3   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 7

Sequence of operations . . . . . . . . . . . . . . . . . . . . 7
Diagnostics/troubleshooting . . . . . . . . . . . . . . . . . 8

E1: Motor overcurrent   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8
E2: Open motor circuit  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8
E3: Motor timed out    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8
E4: Magnum breaker position “unknown”    .  .  .  . 8
E5: Open permissive   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8
E6: Communication error   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8
E8: Position switch error    .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 8

Controller diagnostic display   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9
Controller mounting  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 9
Appendix   .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 10
Disclaimer of warranties and limitation of liability 12

Instructional Booklet

IB013003EN

Effective June 2023

1
2
3
...
»

Содержание Magnum MR2













Отзывы:

Нет отзывов

Похожие инструкции для Magnum MR2

Magnum Air MWN-408

Бренд: Eaton Страницы: 56

Бренд: CHINT Страницы: 6

P3 E(+SVB) Series

Бренд: Eaton Страницы: 2

Бренд: Eaton Страницы: 9

EMS2-DOS SWD Series

Бренд: Eaton Страницы: 7

K-Line Plus KP-8

Бренд: ABB Страницы: 26

Spectra Series AMC6FGB

Бренд: GE Страницы: 4

Бренд: GE Страницы: 4

Бренд: GE Страницы: 2

Бренд: GE Страницы: 5

Бренд: GE Страницы: 4

Бренд: Scame Страницы: 68

DILM95-XSP XTCERENCOILF

Бренд: Eaton Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды