background image

P a g e

 | 

 

Installation and Operation Manual 

Zodiac Aquapure Ei Series APURE35PLGC 

by Zodiac Pool Systems, Inc 

2620 Commerce Way 

Vista, California, 92081 USA 

In US: (800) 822-7933 • In Canada (888) 647-4004 

www.ZodiacPoolSystems.com

Swimming pool algicide/bactericide 

Chlorine Generating Device 

For Residential Pools 

DOMESTIC 

REGISTRATION NO. 30233 PEST CONTROL PRODUCTS ACT  

Installation and Operation Manual 

READ THE LABEL AND OPERATION MANUAL BEFORE USING 

KEEP OUT OF REACH OF CHILDREN 

 

Use Copper Conductors Only 

 

Disconnect Power before Opening Service Cover 

 

For Outdoor or Indoor Use 

 

Electrical Requirements:  120 VAC 50/60 Hz 3 WIRE, 1.3 AMP 

 

Maximum Output of Hypochlorous Acid is Equivalent to 420 g  

 

   of Free Available Chlorine Per Day 

 

4,000 parts per million of salt 

 

The maximum volume of water that can be treated with  

 

    one unit of  APURE35PLGC is 132,000 litres  

 

    (35,000 gallons) (132.0 m

3

). 

 

For swimming pools, a range of 1-3 ppm of free available  

 

    chlorine must be maintained. 

 

Controls bacteria and algae in swimming pool water. 

BUILDER/INSTALLER: Please leave this manual with the pool owner. 
POOL OWNER: Please save this manual.

 

WARNING 

FOR YOUR SAFETY - For anything other than the routine cleaning and maintenance described in this manual, this product 
must be serviced by a contractor who is licensed and qualified in pool equipment by the jurisdiction in which the product will 
be installed where such local requirements exists. In the event no such  local requirement exists, the installer or maintainer 
must be a professional with sufficient experience in pool equipment installation and maintenance so that all of the instructions 
in this manual can be followed exactly. Before installing this product, read and follow all warning notices and instructions that 
accompany this product. Failure to follow warning notices and instructions may result in property damage, personal injury, or 
death. Improper installation and/or operation will void the warranty. 
Improper installation and/or operation can create unwanted electrical hazard which can cause serious injury, property 
damage, or death.  
Operating AquaPure model APURE35PLGC without water flow through the cell can cause a buildup of flammable gases 
which can result in FIRE OR EXPLOSION. 

KEEP OUT OF REACH OF CHILDREN 

 

2012-2869
2012-09-05 

Summary of Contents for 30233


































Reviews: