ZEP DURASHOT S, Instructions Manual

Page: 1 / 6

SURE SHOT
®
SPRAYERS
INSTRUCTIONS
Refillable, reusable. Extra versatile.
Pressurized by free air
DIRECTIONS FOR OPERATING MODEL “M” SPRAYERS
1) ALWAYS DEPRESSURIZE SPRAYER BEFORE
REMOVING ANY PARTS.
The pressure may be let
out of the sprayer one of the two following ways:
a) Tip the sprayer upside down and depress the
trigger until no pressure is left. If some liquid
is left in the sprayer when you attempt this
procedure make sure you aim the nozzle at a
place where a little bit of liquid can be expelled.
b) Remove #122 black cap from air filler and use
small probe to depress #121 valve core until
all the pressure escapes.
NOTE:
Make sure
the sprayer is upright and the air filler stem is
pointing away from you when depressing the
valve core.
c) Remove the complete top assembly from the
canister once all the air has been let out. Do
this by grasping the body in one hand and the
canister in the other while unscrewing
counterclockwise completely.
2)
Fill sprayer 2/3 full (24 ounce maximum liquid
capacity) with light, clean liquid. Make sure the liquid
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.
NOTE: ALWAYS CHECK WITH YOUR CHEMICAL
SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.
READ CAUTION LABEL ON SPRAYER BEFORE FILLING.
NEVER USE ACIDS IN ANY
SURE SHOT SPRAYER.
3)
Take the complete top assembly and screw it
clockwise into top of the canister. Firmly hand
tighten only.
4)
Charge sprayer with compressed air by holding
standard air chuck on valve stem of the air filler.
Hold the air chuck on the air filler until you hear the
line pressure equalize with the sprayer. Working
pressure is 80-150 psi. At least 80 psi is needed to
spray the full 24 oz. without a recharge of air.
THE MAXIMUM PRESSURE SHOULD NOT
EXCEED 200 PSI.
5)
The Model “M” sprayer is now ready to use.
6)
For best results, the liquid to be sprayed should be
lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.
CAUTION:
Never point the nozzle of sprayer toward
yourself or another person. Always point the nozzle
of the sprayer away from yourself and toward your
intended target before depressing the trigger.
MODEL M
24 OZ.
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS
MAXIMUM PRESSURE 200 PSI
SURE SHOT
®
SPRAYERS
INSTRUCTIONS
Refillable, reusable. Extra versatile.
Pressurized by free air
DIRECTIONS FOR OPERATING MODEL “M” SPRAYERS
1) ALWAYS DEPRESSURIZE SPRAYER BEFORE
REMOVING ANY PARTS.
The pressure may be let
out of the sprayer one of the two following ways:
a) Tip the sprayer upside down and depress the
trigger until no pressure is left. If some liquid
is left in the sprayer when you attempt this
procedure make sure you aim the nozzle at a
place where a little bit of liquid can be expelled.
b) Remove #122 black cap from air filler and use
small probe to depress #121 valve core until
all the pressure escapes.
NOTE:
Make sure
the sprayer is upright and the air filler stem is
pointing away from you when depressing the
valve core.
c) Remove the complete top assembly from the
canister once all the air has been let out. Do
this by grasping the body in one hand and the
canister in the other while unscrewing
counterclockwise completely.
2)
Fill sprayer 2/3 full (24 ounce maximum liquid
capacity) with light, clean liquid. Make sure the liquid
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.
NOTE: ALWAYS CHECK WITH YOUR CHEMICAL
SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.
READ CAUTION LABEL ON SPRAYER BEFORE FILLING.
NEVER USE ACIDS IN ANY
SURE SHOT SPRAYER.
3)
Take the complete top assembly and screw it
clockwise into top of the canister. Firmly hand
tighten only.
4)
Charge sprayer with compressed air by holding
standard air chuck on valve stem of the air filler.
Hold the air chuck on the air filler until you hear the
line pressure equalize with the sprayer. Working
pressure is 80-150 psi. At least 80 psi is needed to
spray the full 24 oz. without a recharge of air.
THE MAXIMUM PRESSURE SHOULD NOT
EXCEED 200 PSI.
5)
The Model “M” sprayer is now ready to use.
6)
For best results, the liquid to be sprayed should be
lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.
CAUTION:
Never point the nozzle of sprayer toward
yourself or another person. Always point the nozzle
of the sprayer away from yourself and toward your
intended target before depressing the trigger.
MODEL M
24 OZ.
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS
MAXIMUM PRESSURE 200 PSI
SURE SHOT
®
SPRAYERS
INSTRUCTIONS
Refillable, reusable. Extra versatile.
Pressurized by free air
DIRECTIONS FOR OPERATING MODEL “M” SPRAYERS
1) ALWAYS DEPRESSURIZE SPRAYER BEFORE
REMOVING ANY PARTS.
The pressure may be let
out of the sprayer one of the two following ways:
a) Tip the sprayer upside down and depress the
trigger until no pressure is left. If some liquid
is left in the sprayer when you attempt this
procedure make sure you aim the nozzle at a
place where a little bit of liquid can be expelled.
b) Remove #122 black cap from air filler and use
small probe to depress #121 valve core until
all the pressure escapes.
NOTE:
Make sure
the sprayer is upright and the air filler stem is
pointing away from you when depressing the
valve core.
c) Remove the complete top assembly from the
canister once all the air has been let out. Do
this by grasping the body in one hand and the
canister in the other while unscrewing
counterclockwise completely.
2)
Fill sprayer 2/3 full (24 ounce maximum liquid
capacity) with light, clean liquid. Make sure the liquid
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.
NOTE: ALWAYS CHECK WITH YOUR CHEMICAL
SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.
READ CAUTION LABEL ON SPRAYER BEFORE FILLING.
NEVER USE ACIDS IN ANY
SURE SHOT SPRAYER.
3)
Take the complete top assembly and screw it
clockwise into top of the canister. Firmly hand
tighten only.
4)
Charge sprayer with compressed air by holding
standard air chuck on valve stem of the air filler.
Hold the air chuck on the air filler until you hear the
line pressure equalize with the sprayer. Working
pressure is 80-150 psi. At least 80 psi is needed to
spray the full 24 oz. without a recharge of air.
THE MAXIMUM PRESSURE SHOULD NOT
EXCEED 200 PSI.
5)
The Model “M” sprayer is now ready to use.
6)
For best results, the liquid to be sprayed should be
lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.
CAUTION:
Never point the nozzle of sprayer toward
yourself or another person. Always point the nozzle
of the sprayer away from yourself and toward your
intended target before depressing the trigger.
MODEL M
24 OZ.
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS
MAXIMUM PRESSURE 200 PSI
SURE SHOT
®
SPRAYERS
INSTRUCTIONS
Refillable, reusable. Extra versatile.
Pressurized by free air
DIRECTIONS FOR OPERATING MODEL “M” SPRAYERS
1) ALWAYS DEPRESSURIZE SPRAYER BEFORE
REMOVING ANY PARTS.
The pressure may be let
out of the sprayer one of the two following ways:
a) Tip the sprayer upside down and depress the
trigger until no pressure is left. If some liquid
is left in the sprayer when you attempt this
procedure make sure you aim the nozzle at a
place where a little bit of liquid can be expelled.
b) Remove #122 black cap from air filler and use
small probe to depress #121 valve core until
all the pressure escapes.
NOTE:
Make sure
the sprayer is upright and the air filler stem is
pointing away from you when depressing the
valve core.
c) Remove the complete top assembly from the
canister once all the air has been let out. Do
this by grasping the body in one hand and the
canister in the other while unscrewing
counterclockwise completely.
2)
Fill sprayer 2/3 full (24 ounce maximum liquid
capacity) with light, clean liquid. Make sure the liquid
you are putting into the sprayer is CLEAN and FREE
OF FOREIGN PARTICLES. See ACCESSORIES on
page 3 for liquid filling/measuring device.
NOTE: ALWAYS CHECK WITH YOUR CHEMICAL
SUPPLIER IF YOU ARE NOT SURE OF COMPATIBILITY.
READ CAUTION LABEL ON SPRAYER BEFORE FILLING.
NEVER USE ACIDS IN ANY
SURE SHOT SPRAYER.
3)
Take the complete top assembly and screw it
clockwise into top of the canister. Firmly hand
tighten only.
4)
Charge sprayer with compressed air by holding
standard air chuck on valve stem of the air filler.
Hold the air chuck on the air filler until you hear the
line pressure equalize with the sprayer. Working
pressure is 80-150 psi. At least 80 psi is needed to
spray the full 24 oz. without a recharge of air.
THE MAXIMUM PRESSURE SHOULD NOT
EXCEED 200 PSI.
5)
The Model “M” sprayer is now ready to use.
6)
For best results, the liquid to be sprayed should be
lighter than a No. 10 motor oil. (If liquid is too heavy
a pin stream will result). DILUTE WITH A SUITABLE
DILUENT UNTIL DESIRED SPRAY IS OBTAINED.
CAUTION:
Never point the nozzle of sprayer toward
yourself or another person. Always point the nozzle
of the sprayer away from yourself and toward your
intended target before depressing the trigger.
MODEL M
24 OZ.
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE REMOVING ANY PARTS
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS
MAXIMUM PRESSURE 200 PSI
DURA SHOT
™
S SPRAYERS
DIRECTIONS FOR OPERATING
DURA SHOT
™
S SPRAYERS
DURA SHOT
™
S SPRAYER.
DURA SHOT S
24 oz.
The DURA SHOT sprayer is now ready to use.
2) Connect the sprayer to the quick connect on the
machine (Pictured below). Push the joystick to the
RIGHT (liquid side) of the machine until the yellow
cap on the rod moves all the way to the right
(approx. 15 seconds) and stops.
a) Always use the entire product in sprayer before
you refill as this will make sure you will have 24
oz. on your next fill.
b)
c)
3) Release the control lever; make sure it returns to
center for several seconds, then push lever to the
LEFT for air, and hold for approx. 15 seconds. This
will fill the sprayer with up to 125 P.S.I. of air and
siphon the chemical back into the pump so you are
ready for the next fill. (If you do not hold the lever to
the left long enough the rod will retract slightly
indicating a short fill. Push the lever back to the left
for an additional 5 seconds and release.)
4) Disconnect the quick connect from top of sprayer by
pulling the outside collar of the quick connect until it
releases. You are ready to spray.
CAUTION: Never point the nozzle of sprayer toward yourself
or another person. Always point the nozzle of
the sprayer away from yourself and toward your
intended target before depressing the trigger.
ALWAYS DEPRESSURIZE THE SPRAYER BEFORE
REMOVING ANY PARTS.
SPRAYER NOT RECOMMENDED FOR USE WITH PAINTS.
MAXIMUM PRESSURE 200 PSI.