COOPERATION AND OPERATING RANGE
* 1-channel transmitters do not cooperate with roller blind controllers.
CAUTION: The given range concerns open area - an ideal condition without any
natural or artificial obstacles. If there are some obstacles between a transmitter
and a receiver, it is advisable to decrease the range according to: wood and plas-
ter: from 5 to 20 %, bricks: from 10 to 40 %, reinforced concrete: from 40 to 80 %,
metal: from 90 to 100%, glass: from 10 to 20 %, Over- and underground medium
and high electrical power lines, radio and television transmitters, GSM transmit-
ters set close to a device system have also a negative influence on the range.
Symbol ROP-01 ROP-02 ROB-01 SRP-02 SRP-03 RWG-01 RWL-01 ROM-01 ROM-10 RDP-01 RTN-01
RNK-02
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNK-04
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
P-256/8
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
P-257/4 (2)
180 m
200 m
200 m
200 m
200 m
250 m
180 m
250 m
250 m
180 m
250 m
RNM-10
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
RNP-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNP-02
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RNL-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTN-01
200 m
200 m
200 m
200 m
200 m
250 m
200 m
250 m
250 m
200 m
250 m
RCR-01
160 m
180 m
180 m
lack*
lack*
200 m
160 m
200 m
200 m
160 m
200 m
RTI-01
160 m
180 m
180 m
180 m
180 m
200 m
160 m
200 m
200 m
160 m
200 m
RXM-01
230 m
250 m
250 m
250 m
250 m
300 m
200 m
300 m
300 m
230 m
300 m
RADIO TRANSMITTERS DELETION
Press PROG push-button of ROP-02 device for a longer time. After 5 seconds LED
red diode switches on (signal pulsates) and then it switches off. Release the push-
button in ROP-02 - MEMORY IS DELETED.
TIME PROGRAMMING
Press PROG push-button of ROP-02 device for a longer time till LED red diode
switches on (constant signal). Next release PROG push-button. Wait (for about 5 sec-
onds) till LED red diode switches on (first signal pulsates, next the signal is constant).
Wait again (for about 5 seconds) till LED red diode switches on (first signal pulsates,
next the signal is constant).
for CHANNEL 1:
Press PROG push-button of ROP-02 device and then release it.
LED red diode switches off and then switches on (signal pulsates). Every LED diode
pulse equals 1 second. After the adjusted time is finished (the number of LED red
diode flashes) press PROG push-button and then release it - TIME IS ADDED.
for CHANNEL 2:
Wait again (for about 5 seconds) till LED red diode switches
on (first signal pulsates, next the signal is constant). Press PROG push-button of
ROP-02 device and then release it. LED red diode switches off and then switches on
(signal pulsates). Every LED diode pulse equals 1 second. After the adjusted time
is finished (the number of LED red diode flashes) press PROG push-button and then
release it - TIME IS ADDED.
Maximum time is 18 hours for every channel.
2-CHANNEL WIRELESS CONTROL SET
RZB-04
TECHNICAL DATA
RNK-04
ROP-02
Input (supply) terminals:
-
L, N
Input rated voltage:
3 V DC (battery CR2032)
230 V AC
Battery life:
3 ÷ 5 years
-
Input voltage tolerance:
-
-15 ÷ +10 %
Nominal frequency:
-
50 / 60 Hz
Nominal power consumption:
-
0,39 W „stand-by” mode/
0,69 W operation mode 1 channel/
1,09 W operation mode 2 channels
Number of operation modes:
-
5
Number of channels:
4
2
Transmission:
radio 868,32 MHz
Transmission way:
unidirectional
Coding:
addressing transmission
Maximum number of transmitters:
-
32
Range:
up to 250 m in the open air
Time adjustment:
-
1 s ÷ 18 hours (every second)
Optical signalling:
LED red diode
Input terminals:
-
IN1, IN2
Transmitter’s input (supply) terminals:
-
OUT1, OUT2 - voltage output
Relay contacts parameters:
-
2NO 5A / 250V~ AC1 1250 VA
Number of terminal clamps:
-
6
Section of connecting cables:
-
up to 2,5 mm
2
Ambient temperature range:
-10 ÷ +55
o
C
Operating position:
free
Casing mounting: wall plugs, double-sided adhesive
tape
installation cable box Ø60 mm
Casing protection degree:
IP20 (EN 60529)
Protection level:
III
II
Overvoltage category:
-
II
Pollution degree:
-
2
Surge voltage:
-
1 kV (EN 61000-4-5)
Dimensions:
90 x 80 x 11,5 mm
47,5 x 47,5 x 20 mm
Weight:
0,038 kg
0,039 kg
Reference standard:
PN-ETSI EN 300 220-1,
PN-ETSI EN 300 220-2
PN-EN 60669, PN-EN 60950,
PN-EN 61000
