ZA
CU
TO
PROD
UC
T
IN
S TRUCTION
S
Z
Parts & Features
Canon C100 Z-Finder and EVF Recoil Kit
The Z-Finder Recoil Rig includes our VCT Baseplate and a treaded
bracket and support arm that is screwed to the C100 top handle
providing attachment points and most importantly the support arm
for the Z-Finder attached to the flip out screen. As the Z-finder position
is not optimal for shoulder mounted operation, the VCT Baseplate it is
primarily used on a tripod, slider or dolly. The Canon C100 EVF Recoil
adds the items needed to make this a shoulder mounted rig. It adds
the Axis mount to the C100 handle bracket, and the Z-Mount Zwivel
Grip relocator.
Left Loose
Right Tight
Pull knob out
to reposition.
For additional assembly and individual component features, see numerical figures.
Figure 1:b
Adjusting Rods
(EVF & Z-Finder Recoil)
Attach rods to VCT Plate by loosening
racheting levers, sliding rods into place
and then re-tighten levers.
Figure 1:c
Mounting VCT Plate to VCT-14 Tripod Quick Release Plate
(VCT-14 Sold Seperatly)
(EVF & Z-Finder Recoil)
If needed the tail hook position can be raised or lowered.
Loosen both allen screws equally, raise or lower tail hook
and relock both allen screws when in desired position.
Pull red lever on VCT-14 to release
your Universal VCT Plate.
Mount VCT Plate to VCT-14 by sliding the front wedge into front slot
of VCT-14 and the tail hook around the rear knob of VCT-14.
The VCT-14 will click when the VCT Plate is locked into place.
Figure 2:a
Assembling C100 Grip and Grip Relocator
(EVF Recoil)
*
PRESS
CONNECTOR
FIRMLY
INTO
GRIP
RELOCATOR
UNTIL
YOU
FEEL
A
CLICK
.
*
ATTENTION
:
Insert connecting cable from C100 grip to
grip relocator as shown
Position C100 grip to your liking on the grip
relocator and screw tightly together.
finally, plug cable into C100.
Mount the grip relocator to the rods using
the rod port on your z mount and zwivel.
LEFT LOOSE
RIGHT TIGHT
An alternative mounting method when using a tripod
without a VCT14, is to mount your tripod’s quick release
wedge plate to the wedge on the bottom of the
Universal VCT Plate.
Figure 2:a
(EVF Recoil)
Figure 1:a
Figure 4:a
(EVF Recoil)
Back of C100 Z-Finder Recoil
Adjust rod height by loosening both front
allen screws equally. Slide rods up or down
for desired position and relock allen screws.
From the bottom of the VCT Plate, screw the 1/4”-20 and 3/8”-16
mounting screw into the bottom your camera.
Before securing in place, add on accessories to be used to help find the true
balance of your camera. Align both the VCT and camera’s center of balance
and secure mounting screw in place.
Figure 1:a
Mounting Camera
(EVF & Z-Finder Recoil)
VCT Universal Baseplate Center of Balance
Camera Center of Balance
1
2
1
Universal VCT Baseplate
Tie Down Knob
Racheting
Lever
Tightening
Knob
Z-Finder Pro 1.8x
Orientable
Eyecup
Lens Cap
Focus Ring
1/4-20” Bracket
Screw Hole
C100 Frame
1
1
1
1
1
1
1
1
Lever Usage
*
(EVF and Z-Finder Recoil)
1
C100 Bracket
(Z-Finder Recoil)
1
C100 Z-Finder
(Z-Finder Recoil)
Figure 3:a
(Z-Finder Recoil)
Rod Port
Tightening Lever
1
Racheting
Lever
2
1
Axis Mount with
Racheting Lever
Tie Down Knob
Racheting
Lever
Tightening
Knob
1
1
1
1
1
Grip Relocator with
Z-Mount & Zwivel
(EVF Recoil)
1
C100 Bracket with Axis Mount
(EVF Recoil)
Tail Hook
VCT Wedge Plate
15mm Rods
3/8”-16 Mounting Screw
1/4”-20 Mounting Screw
Racheting Levers
Rod Clamp Riser
Rear Rod Ports
Side 1/4”-20 Mounting Holes
2
1
1
1
1
2
1
2
5/32 & 9/64 Allen Wrench
1
