background image

5VH-F8199-10

LIT-11626-16-35

READ THIS MANUAL CAREFULLY!

It contains important safety information.

This ATV should not be ridden by anyone under 16 years of age.

WARNING

YFM400AR

OWNER’S MANUAL

PRINTED IN USA

2002.06-2.6

×

1 CR

(E)

PRINTED ON RECYCLED PAPER

YAMAHA MOTOR CO., LTD.

EBU00438

LOCATE AND READ OWNER’S MANUAL. FOLLOW ALL INSTRUCTIONS AND WARNINGS.

(For replacement manual, call 1-800-532-1558)

WARNING

ALWAYS

:

  use proper riding techniques to avoid 
  vehicle overturns on hills and rough 
  terrain and in turns.
  avoid paved surfaces-pavement may 
  seriously affect handling and control.

Improper ATV use can result in SEVERE INJURY or DEATH.

NEVER

 operate:

  without proper training or instruction.
  at speeds too fast for your skills or  the
  conditions.
  on public roads-a collision can occur with
  another vehicle.
  with a passenger-passengers affect 
  balance and steering and increase risk  
  of losing control.

ALWAYS USE 

AN APPROVED 

HELMET AND 

PROTECTIVE GEAR

NEVER USE 

ON PUBLIC 

ROADS

NEVER CARRY 

PASSENGERS

NEVER USE 

WITH DRUGS 
OR ALCOHOL

B

E

E

R

B

E

E

R

Summary of Contents for KODIAK Ultramatic


























































































































































































Reviews: