background image

P.O.Box 1, Hamamatsu, Japan

'14.04

Copyright (c) Yamaha Corporation All rights reserved.

This manual is copyrighted by Yamaha and may not be copied or

redistributed either in print or electronically without permission.

1 0 1 2 9 8

SERVICE MANUAL

 CONTENTS

TO SERVICE PERSONNEL  ........................................2–4
PREVENTION OF ELECTROSTATIC DISCHARGE  
......5
REGION MANAGEMENT INFORMATION  
.....................6
FRONT PANEL  
...............................................................7
REAR PANELS  
...........................................................7–9
REMOTE CONTROL PANELS  
..................................... 10
SPECIFICATIONS  
................................................... 11–12
INTERNAL VIEW 
 .......................................................... 13
SERVICE PRECAUTIONS  
...................................... 14–16
DISASSEMBLY PROCEDURES  
............................. 17–18

REWRITING OPU PARAMETER  ............................ 19–25
FRONT PANEL KEYS LOCK MODE  
............................26
BLOCK DIAGRAM  
........................................................27
WIRING DIAGRAM  
.......................................................28
PRINTED CIRCUIT BOARDS  
.................................29–30
SCHEMATIC DIAGRAMS  
.......................................31–42
REPLACEMENT PARTS LIST  
................................44–45
REMOTE CONTROL  
...............................................46–47
SETUP MENU  
...............................................................48
SOFTWARE UPGRADE  
...............................................49

BLU-RAY DISC PLAYER

BD-S677

*

  When the MAIN P.C.B. or Wi-Fi module is replaced, the serial number, new MAC (Wired) address and new 

MAC (Wireless) address MUST be reported to Yamaha Corporation by e-mail.

E-mail: [email protected]

For more information, refer to “SERVICE PRECAUTIONS”.

IMPORTANT NOTICE

This manual has been provided for the use of authorized Yamaha Retailers and their service personnel.
It has been assumed that basic service procedures inherent to the industry, and more speci

fi

 cally Yamaha Products, are already known 

and understood by the users, and have therefore not been restated.

WARNING:

 

Failure to follow appropriate service and safety procedures when servicing this product may result in personal injury, 
destruction of expensive components, and failure of the product to perform as speci

fi

 ed.  For these reasons, we advise 

all Yamaha product owners that any service required should be performed by an authorized Yamaha Retailer or the 
appointed service representative.

IMPORTANT:

 The presentation or sale of this manual to any individual or 

fi

 rm does not constitute authorization, certi

fi

 cation or 

recognition of any applicable technical capabilities, or establish a principle-agent relationship of any form.

The data provided is believed to be accurate and applicable to the unit(s) indicated on the cover.  The research, engineering, and service 
departments of Yamaha are continually striving to improve Yamaha products.  Modi

fi

 cations are, therefore, inevitable and speci

fi

 cations 

are subject to change without notice or obligation to retro

fi

 t.  Should any discrepancy appear to exist, please contact the distributor's 

Service Division.

WARNING:

 

Static discharges can destroy expensive components.  Discharge any static electricity your body may have 
accumulated by grounding yourself to the ground buss in the unit (heavy gauge black wires connect to this buss).

IMPORTANT:

 Turn the unit OFF during disassembly and part replacement.  Recheck all work before you apply power to the unit.

BD-S677

Summary of Contents for BD-S677



















































Reviews: