background image

MODEL 74520SF

“SWINGIN' FREE+”

Swing Set

Assembled dimensions are 168"*91"*74".

Allow 6 - 12 ft of clearance around the perimeter of the swing set area when fully assembled.

OWNER'S MANUAL, ASSEMBLY INSTRUCTIONS, CARE, MAINTENANCE AND USER'S GUIDE

Important Instructions & Warnings

!

Please read this entire instruction and assembly manual completely before proceeding.

You must follow all

safety instructions while using this equipment. The surface area where this swing set is set up must be level and free of
all debris. This set is designed to be anchored into the ground and is not to be set up on any hard surfaces such as
concrete, hardened soil or asphalt. Proper surfacing under and surrounding the set adds to the safety level such as
sand or mulch. Read all cautionary statements on the following pages before using this equipment and save this
instruction manual.

DO NOT ALLOW CHILDREN TO PLAY ON THIS GYM SET UNSUPERVISED! CONSTANT

ADULT SUPERVISION IS REQUIRED

. Do not use when raining or during any inclement weather (i.e. rain, sleet, snow,

ice, high winds, thunderstorms or lightening).

DO NOT ALLOW CHILDREN TO JUMP ON OR CLIMB UP ON THIS

SET'S TOP BAR.

For warranty details and registration see the back page of this manual.

FOLLOW ALL ASSEMBLY INSTRUCTIONS AS WRITTEN IN THIS MANUAL

Please retain sales receipt for warranty purposes.

DO NOT RETURN THE SET TO

THE STORE

. If replacement parts or customer service is needed please contact XDP Recreation by email at

[email protected] or by calling 1-866-884-0535 between 8:00am and 5:00pm (Eastern Standard Time), Monday - Friday. This

gym is designed to be used safely by up to seven (7) children, ages 3 years to 8 years, with weight capacity of 100 lbs per child or total

combined weight limit of 700 lbs for all seven (7) children (318kg). This play gym is designed for backyard use only and is

NOT

intended

for playgrounds, schools, day care facilities, nurseries or other public places.

Follow all assembly instructions carefully and as directed in

this manual

. This gym conforms to all safety requirements by ASTM for Home Playground equipment when properly assembled using the

instructions enclosed. Adult assembly is required. Contains small parts.

For proper stability and safety this gym set should be installed

with ground anchors.

Anchor Kits can be ordered directly from XDP RECREATION at https://www.xdprecreation.com or by calling

1.866.884.0535 or thru your retailer of choice.

Summary of Contents for 74520SF











































Reviews: