WINZO
WINZO
WINZO
WINZO
WINZO
WINZO
Installation Instruction
For One Piece Toilet
Model:WZ5028/AN5028
IMPORTANT!
PRODUCT IS FRAGILE. TO AVOID BREAKAGE AND POSSIBLE INJURY HANDLE WITH CARE
The toilet must be installed by a fully insured and licenced plumber only.
Also be sure the installation conforms to local plumbing and building codes.
TOOLS REQUIRED FOR INSTALLATION
Soft Cloth
or Blanket
Silicone
Silicone/
Caulk Gun
Tape
Measure
Pencil/Marker
Knife
Adjustable
Wrench
Screwdriver
Level
Putty Knife
INSTALL NEW TOILET
REMOVE OLD TOILET
Shut off main water supply prior to installation!
1. Shut off water supply line. If you do not have shut-off valve near the toilet shut off main water supply line.
2. Flush the old toilet and make sure that tank is empty.
3. Disconnect and remove water supply line connected to the toilet's tank.
4. Remove old toilet, bolts, nuts from the closet flange.
5. Clean closet flange area from old wax ring and putty sealant using putty knife from the base area.
6.
Clean any remaining debris and wipe any water at the installation area
7. Temporarily plug flange on a floor with a flange plug or towel to prevent gasses from escaping
,03257$17
7KHPRXQWLQJVXUIDFHDUHDPXVWEHFOHDQGU\
DQGOHYHOHGSULRUWRLQVWDOODWLRQRIWKHQHZWRLOHW
127(
,QVSHFWWKHH[LVWLQJFORVHWIODQJHIRUGDPDJHV,I
GDPDJHGUHSODFHLWWRQHZIODQJHEHIRUHSURFHHGLQJWRWKH
LQVWDOODWLRQ
Thanks for your selecting our products. To ensure this product is installed properly, please read these instructions carefully before you begin.
1.
If it is a new bathroom, install water supply ,shut-off valve,
and toilet flange as necessary to conform to the roughing-in
dimensions.
Bathroom
Wall
Bathroom
Floor
Closet Flange
12"
Rough-in
Figure 1
Step 1
Step 2
90º
90º
3.
Cover the floor with the soft-cloth blanket.
Carfeully turn the toilet on it’s side or
upside-down on the blanket. Install wax ring on
the toilet outlet.(see Figure 2)
Figure 2
4.
Lift and carefully put the toilet over the
closet flange so the closet bolts can go through
the mounting holes in the toilet's base.
Apply
full body weight to rim of bowl for proper
gasket seal
.
(see Figure 3)
Bolt cap
Nut
Bolt Cap Base
Washer
Plastic cover
5.
Install bolt cap bases, washers,nut
and bolt cap over the closet bolts via
the opening holes on both side of
bowl. Do not tighten the nuts. It may
and will cause damage to the toilet's
ceramic base. Then cover the opening
holes with supplied plastic cover. (see
Figure 4)
6.
Connect the water supply line,and
turn on the water. Flush several times,
check for leaks. (see Figure 5)
7.
If necessary, adjust the water level
in the water tank. Turn the adjusting
screw clockwise to raise the water or
Turn the screw counter-clockwise to
reduce water. (see Figure 5)
Refill Tube
Adjusting Screw
Waterline
Supply Line
Shut-off Valve
8.
Make sure the refill tube is
properly inserted into the
overflow pipe of the flush valve.
Refill tube should be positioned
higher than water level. (see
Figure 6)
Overflow Pipe
9.
Install the push button on the tank
lid.Make sure the button rods could
touch the top surface of flush valves
and ensure the buttons match the half
and full flush.
(Button rods could be adjusted by
turning the adjustment nuts)
2.
Inser 2 floor bolts inside of the toilet flange and slide the bolts
through the holes and align bolts horizontaly. (see Figure 1)
Figure 3
Figure 4
Figure 5
RIGHT
WRONG
Water
Level
Figure 6
WinZo
Button Rods
Adjustment nuts
Tank lid
Button Nut
Flush Valve
Half
flush
Full
flush
10.
Put the tank lid on the tank.
Install the seat cover in accordance
with detailed manual on Page 3)
(see Figure 8)
Figure 8
Figure 7
1/3
4-1/2”
