background image

WHITE-RODGERS

FAILURE TO READ AND FOLLOW ALL INSTRUCTIONS CAREFULLY
BEFORE INSTALLING OR OPERATING THIS CONTROL COULD CAUSE
PERSONAL INJURY AND/OR PROPERTY DAMAGE.

DESCRIPTION

This low voltage thermostat is designed to provide con-
venient control of the heating system. To provide greater
room comfort, the sensitive spiral bimetal is combined
with an adjustable heating anticipator to provide maximum
comfort.

R

Operator:  Save these instructions for future use!

If in doubt about whether your wiring is millivolt, line, or
low voltage, have it inspected by a qualified heating and
air conditioning contractor, electrician, or someone famil-
iar with basic electricity and wiring.

Do not exceed the specification ratings.

All wiring must conform to local and national electrical
codes and ordinances.

PRECAUTIONS

This control is a precision instrument, and should be
handled carefully. Rough handling or distorting compo-
nents could cause the control to malfunction.

To prevent electrical shock and/or equipment dam-
age, disconnect electric power to system, at main
fuse or circuit breaker box, until installation is
complete.

Do not short out terminals on gas valve or primary
control to test. Short or incorrect wiring will burn
out heat anticipator and could cause personal
injury and/or property damage.

ATTENTION!

This product contains mercury. There will not be any exposure to mercury under normal conditions of use. This product may replace a unit which contains mercury.
Do not open mercury cells. If a cell becomes damaged, do not touch any spilled mercury. Wearing non-absorbent gloves, take up the spilled mercury with sand
or other absorbent material and place into a container which can be sealed. If a cell becomes damaged, the unit should be discarded. Mercury must not be
discarded in household trash. When this unit or the unit it is replacing is to be discarded, place in a suitable container and return to us at WHITE-RODGERS.

CONTENTS

Description .............................................................................. 1
Precautions ............................................................................. 1
Specifications .......................................................................... 2
Installation ............................................................................... 2

Select Thermostat Location
Route Wires to Location
Attach Thermostat to Wall

Operation & Maintenance ....................................................... 3

Adjusting Heat Anticipator
Calibrating Thermostat

1E30

1F30

CAUTION

Do not use on circuits exceeding 30 volts. Higher
voltage will damage control and could cause shock
or fire hazard.

WARNING

30

10

15

20

25

30

50

55

66

77

88

10

15

20

25

30

WHITE-RODGERS

WHITE-RODGERS

10

25

15 20 25

30

50

58

68

77

88

20

15
10

30

1E30(W) / 1F30(W)

Low Voltage Heating Thermostat

INSTALLATION INSTRUCTIONS

Printed in U.S.A.

WHITE-RODGERS DIVISION

EMERSON ELECTRIC CO.
9797 REAVIS RD., ST. LOUIS, MO.   63123
(314) 577-1300,

FAX (314) 577-1517

9999 HWY. 48, MARKHAM, ONT. L3P 3J3
(905) 475-4653,

FAX (905) 475-4625

PART NO. 37-4877D

Replaces 37-4877C

9524

Summary of Contents for 1E30(W)









Reviews: