1
1
BULL BAR ASSEMBLY
2, 3
2
BRACKET, PASSENGER (2) AND DRIVER (3)
4
2
PLASTIC
PLUG
5
4
RUBBER BUMPER
6
4
1/2-13 x 1.25” HEX HEAD BOLT
7
8
1/2” FLAT WASHER
8
4
1/2” LOCK WASHER
9
4
1/2-13 HEX NUT
1
1
ENSAMBLE DE PARRILLA DELANTERA CON TIRÓN
2,3
2
4
2
TAPONES DE PLÁSTICO
5
4
PARACHOQUES DE HULE
6
4
PIEZA DE SUJECIÓN, LADO DEL ACOMPAÑANTE
Y EL CONDUCTOR
(2)
(3)
”
7
8
ARANDELAS DE PRESIÓN DE 1/2
PERNOS CON CABEZA HEXAGONAL DE 1/2-13 X 1.25
ARANDELA PLANA SAE DE 1/2”
8
4
”
9
4
TUERCAS HEXAGONALES DE 1/2-13
1
1
LA BULL BAR
2,3
2
SUPPORT,COTE PASSAGER (2) ET COTE CONDUCTEUR (3)
4
2
BOUCHON DE PLASTIQUE
5
4
PARE-CHOCS EN CAOUTCHOUC
6
4
1/2-13 X 1.25
RONDELLE A FREIN 1/2 PO
9
4
ÉCROUS HEXAGONAUX 1/2-13
BOULON A TETE HEXAGONALE
PO
7
8
RONDELLE PLATE SAE 1/2 PO
8
4
QTY
CONTENTS - CONTENIDO - CONTENU
TOOLS - HERRAMIENTA
- OUTILS
3/4’’ SOCKET
3/4” WRENCH
18MM SOCKET
18MM WRENCH
RATCHET
TORQUE WRENCH
APPLICATION: 2007-08 TOYOTA TUNDRA
ITEM
AUTOMOTIVE PRODUCTS, INC.
DADO DE 3/4’’
LLAVE DE TUERCAS DE 3/4’’
DADO DE 18MM
LLAVE DE TUERCAS DE 18MM
MANERAL
EXTENSIÓN PARA DADO
LLAVE DE TORQUE
DOUILLE 3/4 PO
CLEF 3/4 PO
DOUILLE 18MM
CLEF 18MM
CLIQUET
RALLONGE DE DOUILLE
CLE DE COUPLE
BULL BAR ASSEMBLY
ENSAMBLE DE PARRILLA
DELANTERA CON TIRÓN
LA BULL BAR
32-2250
32-2255
INSTRUCTIONS-INSTRUCCIONES-CONSIGNES
75-0763 REVISION A 3/17/08
STEP 1.
Remove the contents from box and check for damage. Verify all parts are present. Read instructions
completely before beginning.
STEP 2.
NOTE:
It will be necessary to remove the front license plate and bracket. If local/state laws requires a
license plate, license plate relocation kit 32-0055 is available.
STEP 3.
Locate and remove the 12MM bolts securing the tow hooks to the frame. The tow hooks will not be
reinstalled.
SEE DETAIL A.
STEP 4.
Install the brackets using the factory tow hook bolts. Leave loose.
SEE FIGURES 2 AND 3.
STEP 5.
LIGHT INSTALLATION:
Insert threaded stud on base of the light through hole in cross tube. Using a ratchet, extension
and socket for correct size of nut supplied, insert through large clearance hole in bottom of cross tube.
Thread nut and washers on stud and tighten.
SEE FIGURE 1. NOTE:
A short socket, not a deep well works
best to get the nut started.
NOTE:
Fits most 6" round or rectangle lights. Some lights may require replacing included mount/isolator with rubber
bumpers provided. Mounting stud of 1/2" or less required. Plug mount holes with caps provided if not
installing lights.
NOTE:
Westin advises the installer to use a thread lubricant on all of the
stainless steel fasteners.
Attach Bull Bar to mount brackets using 1/2” stainless steel fasteners.
SEE FIGURE 31 .
Level and adjust Bull
Bar as desired and tighten all fasteners. Recommended torque values are 79 Ft. Lbs. for 12MM bolts and
37 Ft. Lbs. for 1/2” stainless steel fasteners.
WO:
APLICACIÓN: TOYOTA
, MOD. 2007-08
TUNDRA
APPLICATION: 2007-08 TOYOTA TUNDRA
FINISH PROTECTION
Westin products have a high quality finish that must be cared for like any other exposed finish on the vehicle. Protect the finish with a non-abrasive automotive wax, (e.g. Pure
Carnauba) on a regular basis. The use of any soap, polish or wax that contains an abrasive is detrimental, as the compounds scratch the finish and open it to corrosion.
1
2
3
