Parameter
Specifications
Input
DC 10~15V, 300mA max standby 50mA.
Power
Consumption
5.0 Watts max standby 0.6 watts.
Impulse
Output
Multi pulse (normal “High” level)
Inhibit
Input
High enable( +3v~+15v)
Signals
Out1~6
Output
1 pulse/coin
Con2
Input/output
4 pin male
Extend connect port
Con3
Input/output
09FCS
5 pin male
General I/O port
Connector
Con5
Input/output
09UCS 6 pin male
General I/O port
User con trols
5-ch
dip-switch
Sw1, sw2, sw3 for channel or impulse ratio select.
Sw4, sw5 for mode and other function select.
Overall Dimension
(HXWXD)
HI-09UCS: 102x99x55 mm
HI-09FCS: 124.5x120.5x64.5 mm
Speed of acceptable
Max. 3 coins/second.
Diameter
18mm~30mm
Position
1.8
2.2
2.6
3
Coin size
(mm)
Thickness
Adjust
Thickness Range 1.2~2.0
1.2~2.4
1.2~2.8
1.2~3.0
Working temperature 5° ~50°
Weight
HI-09UCS: 240g
HI-09FCS: 300g
HI-09UCS / HI-09FCS
NEW
(Drop inserting type)
(Front inserting type)
Feature
*Support 8 channels (coins) self-programming without PC.
*With an inhibit wire for game board.
*With 6 ch. Parallel output for each channel (coin) control.
*Support one coin then multi pulse output (impulse out ratio).
*With narrow or wide impulse width select (100ms and 50ms).
*Adjustable 4 kinds of coin thickness.
Specifications:
Operation mode:
Before switching on the dc power,
Set DIP 4,DIP 5 to the "OFF" position.
Impulse and channel ratio table (500)
Record mode:
Before switching on the dc
power, set DIP 4, DIP 5 to the "ON"
position.
HUAI I ELECTRONICS CO.,LTD
1
3
5
7
9
2
4
6
8
10
1. GND
2. +12V
3. Output ch5
4. Output ch6
5. Impulse output
6. Inhibit control
7. Output ch1
8. Output ch2
9. Output ch3
10. Output ch4
Accessory
HI-09UCS or HI-09FCS X1
Control board (pcb-09-2) X1
10p Signal cable X1
User manual X1
Screw bag (HI-09FCS only) X1
5P (09F) or 6P (09U) Signal wire X 1
Installation
Case 1:
Using 10p signal cable connect HI-09UCS/HI-09FCS
to control board (pcb-09-2). And need 4 wires connect
control board (pcb-09-2) to game board.
The 4 wires define as below:
1. +12V: for dc power (12 volt).
2. GND: for dc power (ground).
3. IMPULSE: for credit signal (output signal).
4. INHIBIT: control by game board for enable
or disable coin selector (input).
Case 2:
Using 5P or 6P signal wire connect to HI-09UCS/HI-09FCS
another end connect to game board and meter.
+12V
GND
Impulse
Inhibit
DIP SW "X" means off , "O" means on
Please make sure direction
The 5P wire define as below (HI-09FCS only)
1. +12V
2. Counter (Meter)
3. GND
4. Impulse (Credit)
5. Inhibit
The 6P wire define as below (HI-09UCS only)
1. GND
2. +12V
3. +12V
4. Counter (Meter)
5. Impulse (Credit)
6. Inhibit
1
2
3
4
5
6
1
2
3
4
5
Multi coin mode
Out
DIP3, DIP2, DIP1
XXX
XXO
XOX
XOO
OXX
OXO
OOX
OOO
Impulse out Ratio
Impulse out Ratio (bonus)
Ratio
Channel
1
2
3
4
5
6
7
8
1 XXX
1/2
1/4
1
1
1/2
1/2
1/2
1/4
1
2 XXO
1
1/2
1
1
1
1
1
1/2
2
3 XOX 50C
1
1/2
2
2
1
3
2
1+1/2
3
4 XOO 1$
2
1
4
2
2
5+1
4+1
2+1
4
5 OXX 2$
4
2
8
4
4+1
10+2
5+1
4+2
5
6 OXO
5
2
8
4
NA
NA
8+2
5+2
6
7 OOX
8
4
10
10
NA
NA
10+2
NA
6
8 OOO
10
5
10
10
NA
NA
NA
NA
6
(Coin)
DIP SW Function
Select
Action
X
Record 50ms impulse
DIP Sw4
Coin signal
width
(impulse)
O
Record 100ms impulse
O
Normal
DIP Sw5
Blank
O->X->O Makes channel data Blank
V2.9
(500)
MULTI-COIN SELECTOR
FOR EURO COIN
