background image

GARAGE DOORS & OPENERS

Part No.

IMPORTANT NOTICES!

Wayne-Dalton highly recommends that you read and fully  under-
stand the Installation Instructions and Owner’s Manual before you 
attempt this installation. 
To avoid possible injury, read the enclosed instructions carefully  
before installing and operating the garage door. Pay close attention 
to all warnings and notes. After installation is complete, fasten this 
manual near garage door for easy reference.
The complete Installation Instructions and Owner’s Manual are  
available at no charge from:
Wayne-Dalton, a Division Of Overhead Door Corporation, 
P.O. Box 67, Mt. Hope, OH., 44660, 
Or Online At 

www.Wayne-Dalton.com

R

eaR

 M

ount

 L

ow

 H

eadRooM

MH

instaLLation

 

instRuctions

 

and

 

owneR

s

 

ManuaL

t

o R s i o n

Models: 105/110, 

310/311

T a b l e   O f   C o n t e n t s

347785

REV1 03/08/2012

©Copyright 2012  Wayne-Dalton, a Division Of Overhead Door Corporation

Parts Breakdown 

2

Pre-Installation 

3

Important Safety Instructions 

3

Tools Required 

3

Package Contents 

3

Door Section Identification 

4

Graduated End Hinge And Strut Identification 

4

Removing an Existing Door 

5

Preparing the Opening 

5

Installation 

7

Optional Installation 

17

Door Arm Hookup 

17

Lift Handles 

17

Pull Down Rope 

17

Maintenance 

18

Cleaning Your Garage Door 

18

Painting Your Garage Door 

18

Clear Or Stained Finishes 

18

Operation and Maintenance 

18

Warranty 

20

Dealer Locator Information 

22

Summary of Contents for 105/110























Reviews: