background image

Installation Instructions

Please read all instructions before installing

DESCRIPTION AND OPERATION

The RT-50 is a time switch that turns OFF the connected light or fan when the 

selected time expires. The light behind the ON/OFF button illuminates while the 

switch is OFF. One of the time button indicators is always lit to indicate the last 

used timer.

Manual ON

Turn ON the connected light or fan by pressing the desired time button, or the 

ON/OFF button. If you press the ON/OFF button, it activates the timer that was 

last used.

Manual OFF

While a timer is active, you can press the ON/OFF button to turn OFF the 

connected light or fan without delay. 

Changing the selected time

If you decide that you need more or less time than you originally selected, restart 

the time switch by pressing the button that matches the amount of time you think 

you’ll need.

RT- 50

Time Switch

7- Button Preset

   

SPECIFICATIONS

Voltage  ....................................................................... 120VAC, 60HZ

Load (Single Pole Circuit)

  Incandescent or fluorescent lamp  ...........................0 – 600 Watt

  Fan Motor ............................................................................1/6HP

Time Delay...............................................1, 5, 10, 20, 30, 60 minutes

Environment ..............................................................Indoor use only

Operating Temperature ..............................32° to 131°F (0° to 55°C)

Humidity ....................................................95% RH, non-condensing

Tools Needed

  Insulated Screwdriver

  Wire Strippers

Call 800.879.8585 for Technical Support

Santa Clara, CA 95050

Summary of Contents for RT-50







Reviews: