background image

 

WL400 

Manual                                                                                                                                    Page 49 – Revision: 7‐16‐2018 

PRE‐INSTALLATION PROCEDURES 

 

      DANGER!

 

 

ELECTRICAL SHOCK HAZARD.  

Only qualified personnel who have read and understand this entire manual should attempt to 
install, or service this unit, failure to do so could result in death or serious injury.   

 

 

       WARNING!

  

ALWAYS SANITIZE BEFORE USE. 

 Sanitize before use to eliminate any potential microbiological contaminates.     

 

 

Green Compressor/Heater Switch must be in the O=OFF position while the Hot 
Tank is empty.  Damage could occur within one minute and the two Hot Tank 
Overload Devices (High Safety Limit) require manual reset if heater is turned on 
with an empty Hot Tank.  

 

CAUTION!

  

DRIP TRAY DRAIN.

  

If you intend to provide a drip tray drain for your customer, be aware that you 
will be called multiple times per month to service and unclog the tubing leading 
away from the drip tray to drain.  Users will clog the drain with paper clips, 
erasers, napkins, tea bags, gum, and various other intended items.  Waterlogic 
recommends you establish a minimum of weekly visits to the machine for 
cleaning of the drip tray drain. 

 

 

Sanitization of Machine 

 
 

Materials Needed:  

 

Personal Protective Equipment.  Rubber or Nitrile Safety Gloves and Protective Eyewear  

 

Phillips Screwdriver   

 

Temperature Gauge 

 

Water Pitcher or Container to collect water from the faucet 

 

5‐gallon container or drain basin 

 

Sanitizer ‐ Household Bleach (5.25% Sodium Hypochlorite) or Citric Acid Based Cleaner 

 

¼” Plastic Tubing, at least 4 feet in length, and assorted ¼” quick connect fittings 

 

TDS Meter and Test Strips for measuring chlorine – Optional 

 

Sanitizing Cartridge 

 

1.

 

Unpack the 

Waterlogic WL400

 

and check exterior for damage.

 

 

 

Sanitize using a Household Bleach (5.25% Sodium Hypochlorite solution) or other approved 
cleaner throughout the cold and sparkling water circuits.  Follow all instructions on the sanitizer 
and flush with fresh water through the faucet until odor and taste is acceptable. 

 

       WARNING!  

USE PROPER PERSONAL PROTECTIVE EQUIPMENT

 

Always ensure proper ventilation and use proper personal protective equipment such as gloves 
and eye protection when using chemicals.  Refer to Material Safety Data Sheet for specific 
requirements of each chemical product. Take all necessary precautions to prevent sanitizer from 
contacting eyes, clothing, and any other surfaces in could damage (carpets).  

 

 

Summary of Contents for WL400 Series















Reviews: