Waterco DIGIHEAT 10.8kW Installation And Operation Manual Download | Manualshive

Page: 1 / 16

background image

WARNING

!

www.waterco.com

This equipment must be installed and serviced by a qualified technician.
Improper installation may result in property damage, serious injury or death.
Improper installation and/or operation will void the warranty.

Notice to Installer

This manual contains important information about the installation, operation
and safe use of this product. Once the product has been installed

this manual

must be given to the owner/operator of this equipment.

DIGIHEAT TITANIUM

IN LINE SPA HEATERS

Installation and
operation manual for
Single & Three Phase Models

digiHeat 2.4kW - 10A
digiHeat 3.6kW - 15A
digiHeat 4.8kW - 20A
digiHeat 6.0kW - 25A
digiheat 10.8kW - 15A/Phase
digiheat 14.4kW - 20A/Phase
digiHeat 18.0kW - 25A/Phase
digiHeat 24.0kW - 35A/Phase

1
2
3
...
»

Summary of Contents for DIGIHEAT 10.8kW

















Reviews:

No comments

Related manuals for DIGIHEAT 10.8kW

Altherma 3 R F+W

Brand: Daikin Pages: 20

Brand: NARVI Pages: 12

GQ-C3257WX-FF US

Brand: Noritz Pages: 47

Brand: Frico Pages: 28

Brand: Lochinvar Pages: 16

Brand: Nibe Pages: 44

Brand: S&P Pages: 20

Brand: nedis Pages: 36

Brand: Glowworm Pages: 56

Brand: Singer Pages: 36

Brand: Icom Pages: 16

Brand: S&P Pages: 30

LOFT TWIN 6 Bar

Brand: Bathroom Butler Pages: 8

SWUP EXT Series

Brand: Sunsystem Pages: 16

Dura-Power Den & Del

Brand: A.O. Smith Pages: 2

Brand: QualityCraft Pages: 5

Brand: Zodiac Pages: 26

Brand: Daikin Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands