background image

Waterco Limited ABN 62 002 070 733

www.waterco.com

WARNING

!

(8290052) 08/2014

AQUAMASTER

Installation and
Operation Manual

This equipment must be installed and serviced by a qualified technician.
Improper installation can create electrical hazards which could result in property
damage, serious injury or death. Improper installation will void the warranty.

Notice to Installer
This manual contains important information about the installation, 
operation and safe use of this product. Once the product has been installed 
this manual must be given to the owner/operator of this equipment.

OFFICES - AUSTRALIA

NSW - Sydney
(HEAD OFFICE) 

 

Tel : +61 2 9898 8686
VIC/ TAS - Melbourne
Tel : +61 3 9764 1211
WA  - Perth
Tel : +61 8 9273 1900
QLD - Brisbane
Tel : +61 7 3299 9900
SA/ NT - Adelaide
Tel : +61 8 8244 6000
ACT Distributor
Tel : +61 2 6280 6476

OFFICES - OVERSEAS

Waterco USA
Augusta, USA
Tel : +1 706 793 7291
Waterco Canada
Longueuil, Qc, Canada
Tel : +1 450 748 1421
Waterco (Europe) Limited
Sittingbourne, Kent. UK 
Tel : +44(0) 1795 521 733
Waterco France
SAINT PRIEST, France 
Tel : +33 (0)4 72 79 33 30
Waterco (NZ) Limited
Auckland, New Zealand
Tel : +64 9 525 7570

Waterco (C) Limited
Guangzhou, China
Tel : +8620 3222 2180
Waterco (Far East) Sdn. Bhd.
Selangor, Malaysia
Tel : +60 3 6145 6000
PT Waterco Indonesia
Jakarta, Indonesia
Tel : +62 21 4585 1481
Waterco International Pte Ltd
Singapore
Tel : +65 6344 2378

Summary of Contents for Aquamaster

























Reviews: