FRONT BUMPER & FRONT GRILLE
Mercedes Benz
G-class
(W463)
Recommend to paint protective coating
on the back side of WALD Over Fender.
2013/04
【BEFORE PAINTING】
１） Remove OEM front bumper according to the Mercedes-Benz service manual.
※Use the bracket (sold separately) to fix OEM intercooler to the body only for Turbo Model.
２） Relocate all the necessary OEM parts and WALD Front Grille to WALD Front Bumper.
※ Adjust the details of WALD Front Bumper to fit the body by rasps or sandpapers.
３） Paint WALD Front Bumper and Front Grille according to the picture.
【AFTER PAINTING】
４） Install the attached meshes to WALD Front Bumper and Front Grille with caulking glue.
５） Fix the attached LED lamps and WALD Front Grille to WALD Front Bumper.
※ Adjust optical axis, and make sure the LED lamps are fine to work before the installation.
６） Temporarily fix the attached rubber moldings to WALD Front Bumper.
７） Check all the balance of the location and fitting,then tighten all the OEM and attached bolts.
８） Cut the pins on the back of OEM front grille emblem,
and use the caulking glue to fix it on WALD Front Grille.
※ Leave it till completely fixed.
※ MORE THAN 2 TECHNICIANS ARE NECESSARY IN THIS WORK.
DURING ALL THE INSTALLATION PROCESS, PLEASE BE CAREFUL NOT TO DAMAGE THE BODY.
※ ADJUST ALL THE DETAILS OF OUR PRODUCTS TO FIT ON A CAR PERFECTLY.
ADD: 10-13 KYOGUCHI-CHO, TAKATSUKI, OSAKA, JAPAN
WALD. INTERNATIONAL
ZIP: 569-0072 TEL: (81)-72-673-3000 FAX: (81)-72-673-3003
ATTENTION
ATTACHED LED LAMP
ATTACHED BOLTS (M6 x 12) & RUBBER WASHERS
※Fix WALD Over Fender and Front Bumper together.
OEM EMBLEM
※Cut the pins on the back.
OEM BOLTS
※Fix OEM bolts through the attached brackets
on WALD Front Bumper.
OEM BOLTS
※Fix OEM bolts with the OEM fixture.
WALD FRONT GRILLE
※Use the attached bolts (M6 x 12)
to fix from the rear of WALD Front Bumper.
ATTACHED
RUBBER MOLDING
INSTALLATION MANUAL
Completely degrease and paint primer on all
the installation positions to enhance the viscidity
of double sided tape.
Use dryer to warm double sided tape to enhance
the viscidity in low temperature.
Keep the car in a dry condition more than
24 hours after gluing.
Do not wash the car during this time.
THANK YOU FOR PURCHASING. THIS IS THE INSTALLATION MANUAL OF WALD FRONT BUMPER FOR MERCEDES-BENZ W463 G-CLASS.
PLEASE READ THIS MANUAL CAREFULLY BEFORE THE INSTALLATION.
※ NO RETURNS CAN BE ACCEPTED BECAUSE OF IMPROPER INSTALLATION OR PAINTING.
※ CHECK THE FITMENT, AND ADJUST ALL THE DETAILS BEFORE PAINTING.
Please purchase double sided tape,
primer and caulking glue at
auto accessory shop or hardware store.
Use caulking glue
to fill the gap
between the product
and the body.
※ PLEASE BE AWARE OF:
■ You may lose the warranty and all the services from the car maker, because of replacing OEM parts.
■ Reduced road clearance may cause inconvenience in using parking curbs and garage jack.
■ FRP, ABS and PPE products are slightly weaker than OEM parts in crashes.
■ The product may not match the body and OEM color perfectly.
■ We assume no responsibility for any damage resulting from improper installation, painting,
modification and any cut wound in unsealing.
■ Contact the car dealer when you have any question in removing OEM parts.
■ During all the installation process, use parking brake and stop the engine completely.
■ Use rasps or sandpapers to fit the products to the body if there is an individual difference.
■ The product is made of FRP. Handle with care. Do not give the excessive force.
Gradually fix the bolts and nuts by checking the fitment and balance of the installation.
■ Check the fitment, and adjust all the details of the fitment steady and proper.
Please check the fitment and all the details regularly, fix the bolts and nuts as necessary.
■ The instruction of painting is just our recommendation, please paint it as you like.
PARTS
QUANTITIES
1
1
1 SET
1
1 SET
1 SET
14
6
FRONT BUMPER
FRONT GRILLE
MESHES FOR FRONT BUMPER
MESH FOR FRONT GRILLE
LED LAMP KIT
RUBBER MOLDING
BOLTS (M6 x 12)
RUBBER WASHERS
FRONT BUMPER
ATTENTION
ATTACHED MESH
MATTE BLACK
■HOW TO INSTALL THE ATTACHED MESHES
(STEP 4)
Use pins and caulking glue to install
the attached meshes to WALD Front Bumper
from the rear.
※Paint the inside of the ducts and pins in black.
■WALD SHOWCAR IS PAINTED LIKE THE PICTURE (STEP 3)
Make clear coating for the carbon parts
of WALD Front Bumper.
INTERCOOLER
OEM BOLTS
OEM NUT
OEM PLASTIC NUT
BRACKET
■HOW TO FIX OEM INTERCOOLER TO THE BODY (Step 1)
BRACKET (SOLD SEPARATELY)
MBMANUALS.COM
