background image

 

 

 

 

Service Manual for VT-DS300SS-2Z and VT-DS300SS-2Z-L 

This wine cooler should be serviced by a qualified technician. 

Be sure to have the unit unplugged while repairing the unit

 

Tools Required: 
1. 

Tool for Electrical Apparatus Troubles: multi-meter, split-core type meter, power meter, Philips 

screwdriver, long flat nose pliers, vice, power board, control board, etc.   

2. 

Tool for Cooling Troubles: suds, brush, R134a gas, nitrogen, oxygen/acetylene soldering set, 

oxygen,  acetylene,  ø6X0.7copper  tube,  ø4X0.7copper  tube,  silver-copper  brazing  alloy,  scaling 
powder, etc. 
 
Troubleshooting & Maintenance: 

I. 

Troubleshooting for Electric Control: 
1. 

Unworking Display. Display does not appear to be working, Display does not appear 
to be working after the appliance is turned on. 
(1) 

Please refer to the clearance procedures below: 

No display in the control panel. 
Check if the electricity is available in the socket. →No. →Repair the socket. 
Yes. →Open the terminal box lid of the medium air duct pane. 
Yes. →Check if the wires of terminals are connected rightly. 
Loose  →Connect  the  terminals  rightly  or  change  it.  →Inspect  it  with  power-on.  →  OK.  → 
Trouble clearing. → Still not normal. 
OK. → Change with a normal control panel. 
Inspect it with power-on →OK. →Change the control panel. → Inspect it with power-on. → OK. 
→ Trouble clearing. → Still not normal. 
Not normal. → Change the PC board. 
Inspect it with power-on. →OK. →Change the PC board. → Inspect it with power-on. → OK. 
→ Trouble clearing. → Still not normal. 
Not normal. → Change the PC board and the control panel. 
Inspect it with power-on. →OK. →Change the PC board and the control panel. → Inspect it 
with power-on. →OK. → Trouble clearing. → Still not normal. 
Not normal. → Check if each 7P terminal is short circuit or open circuit. 
Repair 7P terminals. 
Inspect it with power-on. → OK. → Trouble clearing. → Still not normal. 

 

                                                                                           

 

Summary of Contents for VT-DS300SS-2Z



















Reviews: