Application Drawings
IP Camera-end Installation
- Install a Vi2701TX at the camera side. It can be powered in 2 ways.
1- Using Local Power Supply:
Connect the 48-56 VDC power supply to
the power connector of the Vi2701TX. A power adapter connector is
provided to simplify connection.
2- Using PoE:
If no local power supply is plugged in, the unit will use PoE
power provided by the Vi2701RX or Vi2500 series at the head-end.
- Connect the IP camera RJ45 connector to the “10/100BaseT Ethernet”
port of Vi2701TX using a standard Cat5/6 cable of maximum 100m in
length.
- Connect one end of the long UTP cable to the “Extended Ethernet” RJ45
connector of Vi2701TX.
The link LED on the 10/100 connector should be “ON” to indicate proper
connection between the camera and Vi2701TX.
Ethernet Switch/NVR-end Installation
There are 3 options for the equipment installed at the control room:
1- Use Vi2701RX:
You can use a Vi2701RX to connect to Vi2701TX at the camera location.
- Connect the Vi1120 or a similar 52-57 VDC at 70W or more power supply
to the power connector of the Vi2701RX. A power adapter is provided to
simplify connection if needed.
- Connect the RJ45 connector of the Ethernet switch to the 10/100BaseT
Ethernet port of Vi2701RX using a standard Cat5/6 cable of maximum 328
feet (100 m) in length.
- Connect one end of the long UTP cable to the “Extended Ethernet” RJ45
connector of Vi2701RX.
The link LED on the 10/100 Ethernet connector should be “ON” to indicate
proper connection between the switch and Vi2701RX.
When Vi2701RX and Vi2701TX make a connection, the Vi2701RX will
provide power to Vi2701TX and the camera. While the Link LED, Orange for
100BaseT and Green for 10BaseT, is in a steady state it will indicate
confirmed connection between extenders.
2- Use Vi2508/Vi2516 (port 1-4)
- Connect an Ethernet port of the Network switch to the one of the port 1-4 of
Vi25xx using a standard Cat5/6 cable of maximum 328 feet (100 m) in
length.
- Connect one end of the long UTP cable to the “Extended Ethernet” RJ45
connector of Vi25XX.
The link LED on the 10/100 Ethernet connector should be “ON” to indicate
proper connection between the switch and Vi25XX.
Vi2701TX UTP Ethernet and PoE Extender Installation Manual
DO NOT OPEN
RISK OF ELECTRIC SHOCK
CAUTION
CAUTION:
TO REDUCE THE RISK OF ELECTRICAL SHOCK,
DO NOT REMOVE COVER. NO USER SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
The Smart Choice for Transmission Solutions
www.vigitron.com
Important Safety Warning
- Read these instructions.
- Keep these instructions.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- Install in accordance with the manufacturer’s instructions.
- This installation should be made by a qualified service person and should
conform to all local codes.
- DO NOT bundle UTP or Coax signals in the same conduit as high-voltage
wiring.
- To reduce the risk of fire or electrical shock, do not expose these products
to rain, moisture, dripping or splashing.
- No objects filled with liquids, such as vases, shall be placed on Vigitron
equipment.
- DO NOT install the unit in a place where the operating ambient tempera
ture exceeds 75° C.
- Make sure that the external power supply output voltage is in the recom
mended range.
- Do not install near any heat sources such as radiators, heat registers,
stoves or other apparatus (including DVRs) that produce heat.
- Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.
- Only use attachments/accessories specified by the manufacturer.
- Unplug this apparatus during lightning storms or when unused for long
periods of time.
- Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as a power
supply cord or plug is damaged, liquid has been spilled, or objects have
fallen into the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
- The mains plug is used as the disconnect device and shall remain readily
operable.
WARNING! - To reduce the risk of fire or electric shock, do not expose
this apparatus to rain or moisture. This apparatus shall not be exposed to
dripping or splashing and no objects filled with liquids, such as vases shall
be placed on the apparatus.
WARNING! - This apparatus is a Class I product. This product must
be connected to a main socket outlet through an AC to DC Power supply.
WARNING! - The main plug is used as the disconnect device and
shall remain readily operable.
Vi2701TX_UM
The MaxiiCopper Model Vi2701TX is a revolutionary transmission device
that extends full-duplex High-Speed Ethernet and High power PoE over
existing UTP infrastructures. It extends 10BaseT signals up to 3,000 feet
(914 m) and 100BaseT up to 2,100 feet (640m). It employs MaxiiCopper™
innovative and unique Ethernet extension technology that is designed to
take full advantage of high-bandwidth networking cables and maintain a
full-duplex 10 or 100 Mb/s Ethernet connection up to the maximum range
with minimum transmission error and latency.
The Vi2701RX is installed at the control room and can provide up to 74W
power to Vi2701TX at the camera side. The Vi2701TX supports both
single PD or dual PD IP cameras. The Vi2701TX also provides an extra
40-56VDC output that can be used for auxiliary equipment related to the
camera. The Vi2701TX can operate with Vi2701RX and Vi2500 series.
The Vi2701TX includes unique features that assure high performance
required to support the largest Megapixel cameras. It is equipped with
LEDs to provide link status and configured data rate. No IP setting or
configurations are required and it is completely transparent to the corporate
IP network and higher layer protocols. The UTP cable needs to be point to
point without any branches. Multiple segments can be joined together using
UTP couplers.
Max
ii
Copper
TM
Vi2301A
Cat 5/6
The Vi2701RX can be used with a Vi2701TX to power a PoE camera and provide DC power to an IR light over extended UTP.
Powering a PoE camera and an IR light over extended UTP
Data +
60W PoE
Extended Cat5/6
+48VDC
Data +
PoE
328 ft. (100m)
PoE Camera
Network Switch
Vi2701TX
Vi2701RX
IR
The Vi2701TX can be used with a Vi2516 extended UTP PoE Midspan to power a PoE camera and provide DC power to an IR light.
Powering a PoE camera and an IR light over extended UTP
Data
Data
+48VDC
Data +
PoE
328 ft. (100m)
PoE Camera
Vi2516
Network Switch
Vi2701TX
IR
Power
Supply
The Vi2701TX can be used with a Vi2301A to power a PoE camera and provide DC power to an IR light over extended UTP.
Powering a PoE camera and an IR light over extended UTP
Data +
60W PoE
Extended Cat5/6
+48VDC
Data +
PoE
328 ft. (100m)
PoE Camera
Vi2701TX
IR
PoE Switch
Data +
60W PoE
328 ft. (100m)
