background image

VEC-1856 Instruction Manual 

6 Meter Ground Plane Antenna 

VEC-1856  6 METER GROUND PLANE ANTENNA 

 

INTRODUCTION 

 

The VEC-1856 Ground Plane Antenna features a DC grounded element and a ground 
isolated radial system for improved performance. 
  
The ground isolated radial system, unique to the VEC-1856 antenna, reduces undesirable 
feedline and supporting structure radiation by eliminating common mode current paths.  
This unique system improves transmission by producing a much cleaner pattern with 
more signal at desired angles, and also reduces conducted noise reaching the antenna over 
the outside of the feedline or antenna support.  It also insures that the length of the 
feedline or support does not change the antenna's resonant frequency or SWR. 
 
The VEC-1856 is easily cut for the desired area of the six meter band.   A rugged low 
impedance air insulated matching stub provides convenient adjustment of base impedance 
(a normal ground plane is much less than 50 ohms) allowing adjustment to a perfect 1:1 
SWR.  Power capability is 1000 watts RF continuous.  

 

CHOOSING A LOCATION FOR THE ANTENNA 

 

WARNING: 

Improper installation and assembly can be 
hazardous! Read these instructions thoroughly 
before attempting to assemble, install or operate 
this product!   Always mount this antenna so that 
it is out of the reach of adults as well as 
children. High power transmitting devices produce 
voltages that can cause severe burns or other 
injuries. 

 

For the best performance on receiving and transmitting, mount this antenna in a clear 
location at least a few feet above or 20 feet away from buildings, towers, feedlines, utility 
wires, and other antennas. While your own ingenuity and particular circumstances will 
determine the final mounting method, we will pass along some rules that can not be 
neglected. 
 

Never

 mount this antenna in a location that will permit unsuspecting people to come in 

contact with the radials or any other part of the antenna. 

 
Never

 mount this antenna where a mechanical failure might allow the antenna to contact 

power lines or other utility wires. 

 
Always

 ground the feed line at the point where it enters a building to a good earth ground 

for lightning protection. 
 

Summary of Contents for VEC-1856










Reviews: