background image

Vado

Wedmore Road, Cheddar, Somerset, England BS27 3EB

tel 01934 744466.      fax 01934 744345

[email protected]

www.vado-uk.com

  guarantee

  customer/technical services

For any technical or installation queries please contact Vado on 01934 745163.

GUARANTEE REGISTRATION

NAME
ADDRESS

RETAILER
ADDRESS

PURCHASE DATE
PRODUCT DESCRIPTION
WHO INSTALLED THE PRODUCT?
FOR VADO USE

POSTCODE

POSTCODE
ARTICLE NUMBER

(SEE BOX)

RETAILER

PLUMBER

BUILDER

SELF

This product is guaranteed against manufacturing defects from the date of purchase until the expiry of the relevant 
guarantee period shown below.

The guarantee is only valid if:-

1. The product has been installed, used and maintained in accordance with Vado’s instructions and subjected to 
normal use only.
2. The defect is not due to use of an unsuitable or inadequate water or power supply.
3. The defect is not due to accident, misuse, neglect or repair other than by Vado or Vado authorised agents or 
damage caused by foreign objects or substances.
4. We have received from you the completed Guarantee Registration Form. Vado accepts no responsibility for any 
forms lost in the post and returns by registered means is therefore recommended.
Under this guarantee (which is non-transferable) Vado will, at its option, repair or replace free of charge any product 
(or replacement part) found to be defective. The guarantee does not extend to any consequential loss or damage. 
After repair or replacement the relevant guarantee period will be calculated from the original date of purchase.

The relevant guarantee periods are:-

1. Twelve years on chrome finish products.
2. Three years on all other products with the exception of Stuart Turner Pumps which carry a 2 year Guarantee on 
Monsoon Range and 1 Year Guarantee on Showermate Range.
All claims under the guarantee must be submitted in writing to the person who supplied the product to you and 
must be received no later than the last day of the relevant guarantee period. All claims must be accompanied by 
proof of purchase (sales receipt or delivery note).
Vado operates a policy of continuous product development and therefore reserves the right to change the product, 
packaging and documentation specifications without notice.
This guarantee is in addition to and does not affect your statutory rights as a consumer.

installation & maintenance instructions 

mono bidet mixer

please leave these instructions with the customer

synergie

Syn 110.indd   1

10/2/10   11:03:13

Summary of Contents for synergie

Page 1: ... and returns by registered means is therefore recommended Under this guarantee which is non transferable Vado will at its option repair or replace free of charge any product or replacement part found to be defective The guarantee does not extend to any consequential loss or damage After repair or replacement the relevant guarantee period will be calculated from the original date of purchase The re...

Page 2: ...upply Water Fittings Regulations 1999 Schedule 2 Section 6 G15 13 2 Before making any inlet pipe connections all supply pipes MUST be thoroughly flushed to remove debris Failure to do so could result in damage or low flow from the mixer unit Water Supply Water Fittings Regulations 1999 Schedule 2 Section 4 G13 1 The fitting of isolating valves to the inlet feeds is advised for ease of maintenance ...

Page 3: ...e mixer lever forwards will actuate the flow of water and progressively increase the water temperature 69mm 2 x G1 2 65mm 116mm 43mm max 180 mm 88 7mm max 50mm 125mm max 40mm 88mm 70mm 25mm 63mm 41mm 109mm 5 15 G 1 1 4 6mm 44 45mm 38mm Pull the vertical control rod up to close the waste outlet and push down to open Syn 110 indd 3 10 2 10 11 03 14 ...

Page 4: ...e installing your new mixer flush through the pipework to ensure removal of debris turn off the water supply Make sure that the mixer seal is in position against the mixer body Position the mixer on the basin From the underside of the basin fit the rubber washer onto the threaded rod followed by the metal washer and the locking ring Screw the locking ring up until the bolts touch the washer Tighte...

Reviews: