background image

Installation and User Guide 

 

 

 

 
 
Camera and Electronic Products for Integrators 

2006 Vaddio - All Rights Reserved.  Reproduction in whole or in part without written permission is prohibited.  Specifications and 

pricing subject to change.  CeilingVIEW, WallVIEW ControlVIEW, Quick-Connect, EZCamera and PowerRite are registered 
trademarks of Vaddio, Inc. All other trademarks are property of their respective owners. Form Number 341-141 Rev. C. 

WallVIEW

 50i PTZ HideAway 

Installed PTZ Wall Camera with Recessed, Motorized In-wall Camera Lift System 

 
 
 
 
 
 
 
 
 

 

The Vaddio WallVIEW 50i PTZ HideAway Camera System is a 
mechanically unique and complete product that was designed to 
provide system integrators with an easy to install, in-wall, recessed 
and motorized camera lift system for use when cameras require 
concealment for security or architectural design purposes.  The 
WallVIEW 50i features the Canon

® 

VC-C50i pan/tilt/zoom camera 

which is mounted in a recessed plenum rated enclosure with a 
motorized front panel door.  When closed, the WallVIEW HideAway 
enclosure conceals the camera until the camera is activated, then 
the front door drops down and reveals the camera to the meeting 
room participants.   

 

The system is equipped with Vaddio’s EZCamera™ Cabling 
System.  This allows the integrator to use Cat. 5 cabling to run 
power and video together on a single Cat.5 and camera control on 
a second Cat. 5 run.  The VISCA control interface is included to 
allow the camera to work with any other VISCA compatible control 
device. The PowerRite™ power supply regulates the right amount 
of power needed for the camera over the Cat. 5 cabling.  

 

 

Before operating the Vaddio WallVIEW 50i PTZ HideAway, please 
read the entire manual thoroughly. The camera system was 
designed, built and tested for use indoors and with the provided 
power supply. The use of a power supply other than the one 
provided or outdoor operation has not been tested and could 
damage the camera and/or create a potentially unsafe operating 
condition. 

 

The information contained in this manual will help you install and 
operate your Vaddio WallVIEW 50i PTZ HideAway.  If these 
instructions are misplaced, Vaddio keeps copies of Specifications, 
Installation and User Guides and most pertinent product drawings 
for the Vaddio product line on the website.  These documents can 
be downloaded from 

www.vaddio.com

 free of charge.   

SAVE THESE 
INSTRUCTIONS 

INTENDED USE 

INTRODUCTION 

Summary of Contents for WallVIEW 50i















Reviews: