UV Pure Technologies Hallett Instructions Manual Download | Manualshive

Page: 1 / 12

background image

Instructions for the 4-20mA Unit

DO NOT REMOVE FRONT PANEL WITHOUT REVIEWING
INSTRUCTIONS FIRST. DAMAGE TO DISPLAY(S) MAY
RESULT.

Please read entire instruction before proceeding with
installation or operation of the 4-20mA unit.

4-20mA Unit / Unité / Unidad

Intensidad de los rayos ultravioleta

Transmisión neta de los rayos ultravioleta

UV Intensity

Intensité des rayons UV

Transmittance UV nette

Net UV Transmittance

On Board

4-20mA Option

Figure 1

1
2
3
...
»

Summary of Contents for Hallett













Reviews:

No comments

Related manuals for Hallett

Brand: GC Water Pages: 15

750-626/020-002

Brand: WAGO Pages: 60

Brand: waterlovers Pages: 12

Brand: Autopot Pages: 2

FlowMAX FM Series

Brand: USFilter Pages: 52

Brand: AEG Pages: 388

Brand: brondell Pages: 60

Brand: Bluewater Pages: 2

Brand: claber Pages: 4

Brand: claber Pages: 22

Brand: Clack Valves Pages: 52

Spa & Pool UV-C 140000

Brand: Certikin Pages: 16

Brand: P3 International Pages: 1

Global Drive 54 A

Brand: Lenze Pages: 64

Brand: MAC Pages: 25

Brand: Maytag Pages: 16

Brand: A.O. Smith Pages: 54

Optimax-XXL DN300

Brand: Graf Pages: 22

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands