![background image](http://html.mh-extra.com/html/urban-ambiance/uql1104/uql1104_installation-instructions_1061529001.webp)
Hardware Contents
Package Contents
1of2
D
B
Cage
x 1
Tab
x 2
AA
Crossbar Assembly
x 1
STEP 1
Install Shade
-
A. Place Glass Shade (C) into the Cage
(D), secure by place the Tab (B) into
the Cage (D) press on the Glass
Shade (C).
B. Set the Cage (D) with Glass Shade
(C) into the Cap on the Fixture Body
(A), secure by threading the Lock
Screw (E) into the Cap, tighten until
sung.
Figure 3
A
Fixture
Body
x 1
C
Glass Shade
x 1
Figure 1
Mounting
Ball
Mounting
Screw
Hex Nut and
Lock Washer
STEP 2
Install Inner Backplate
-
A. Pass the supply wires through the Crossbar Assembly (AA). Attach
the Crossbar Assembly (AA) to the Outlet Box with the head of the
Green Ground Screw facing you. Secure it with Outlet Box Screws
(not included). Tighten until snug
.
Supply Wires with
Ground Wire
AA
Outlet Box Screws
(not included)
Outlet Box
Figure 2
STEP 3
Fit Fixture Body to
Crossbar Assembly
-
A. Remove mounting balls from the
Crossbar Assembly (AA). Fit the
Fixture Body (A) Crossbar
Assembly (AA) and secure with
mounting balls. Note: The
backplate of the Fixture Body (A)
should be snug against the wall
surface and the mounting balls. If
not, adjust the length of the nipple
on the Crossbar Assembly (AA) by
unscrewing the preassembled hex
nut and lock washer and then
screwing the mounting screws in or
out of the crossbar until the correct
length is achieved. Once the
backplate of the Fixture Body (A) is
secure, remove the mounting ball
and Fixture Body (A) and proceed
to Step 4.
E
Lock Screw
x 3
A
B
C
D
E
AA
A
Tools
Required:
Flathead
screwdriver,
Phillips
screwdriver,
pliers,
wire
cutters,
wire
strippers,
electrical
tape,
safety
glasses.
Bulb
Recommended:
(3)
Candelabra
Base
60W
Maximum, Alternate
bulb
(3)
13W
CFL
Estimated
Assembly
Time:
30-45
minutes
Preparation:
Identify
and
inspect
all
parts
before
beginning
installation.
Check
package
content
list
and
diagrams
below
to
be
sure
all
parts
are
present.
If
any
parts
are
missing
or
damaged,
do
not
attempt
to
assemble,
install,
or
operate
the
fixture.
Contact
customer
service
for
replacement
parts.
Fixture
can
only
be
mounted
in
the
direction
indicated
on
page
2.
Warnings and Cautions
Turn off electricity at circuit breaker or main fuse box before installation. Consult a licensed electrician if in doubt.
These instructions are provided for your safety. It is very important you read them completely before installing the fixture. We strongly
recommend that a licensed, professional electrician perform the installation.
Disconnect fixture from power source before replacing bulbs. Make sure bulbs are given sufficient time to cool before removal. Do not subject
glass parts to any shock while in operation or shattering may result.
STEP 4 - Wire Connections
A. Use standard wire connectors (not included) to make all wire
connections. (Connectors are not included with fixture.) Twist
connectors until wires are tightly joined together. Wrap each
connection with approved electrical tape and carefully stuff all the
connected wires into the Outlet Box.
Installation Instructions:
UQL
1
104
www.urbanambiance.com