Upland 207P Installation And Operation Manual Download | Manualshive

Page: 1 / 33

background image

INSTALLATION

AND OPERATION

UPLAND® 207 PELLET STOVE

Thank you purchasing our stove. With proper
installation, operation, and maintenance this stove
will provide you with warmth and hearth enjoyment
for decades. Please take the time to review the
proper installation and operating procedures.

This is a natural draft pellet stove. That is not
common. However, it is part of the design that
provides an awesome fire view, trouble free
operation, and great flexibility in the quality of the
pellets that you may burn.

CRITICAL - THE VENTING:

The Upland 207P Pellet

Stove must be installed following the National Fire
Protection Agency 211 and ASTM 1059 guidelines
for a natural draft solid fuel appliance. The flue must
clear the roof line and rise two feet above any portion
of the roof that is within ten feet. That is standard for
a wood stove or coal stove. (This type of installation
eliminates most back draft and shut down problems
and keeps the side of your home free of hydrocarbon
deposits.)

If you are replacing another solid fuel heater and
connecting to an existing solid fuel chimney this is
not an issue if your original installation is up to code.
You should already be in compliance. A standard

1
2
3
...
»

Summary of Contents for 207P


































Reviews:

No comments

Related manuals for 207P

Brand: RAIS Pages: 13

Brand: hergom Pages: 80

TERMOROSSELLA PLUS EVO DSA 4.0

Brand: LA NORDICA Pages: 116

Brand: BCP Pages: 8

Brand: Harman Stove Company Pages: 20

Brand: Acquisitions Pages: 10

Brand: RAIS/attika Pages: 376

italy termo dsa

Brand: Nordica Pages: 68

Brand: NESTOR MARTIN Pages: 88

Brand: Primus Pages: 50

Advantage II-T C FS

Brand: Whitfield Pages: 48

Brand: Whitfield Pages: 48

Advantage Optima 2 FS

Brand: Whitfield Pages: 54

Brand: Palazzetti Pages: 12

Brand: Hardy Pages: 42

Brand: HearthStone Pages: 32

Built In Fanned 60cm

Brand: STOVES Pages: 16

Brand: Fireline Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands