UT075Z_PMR446MR-2CK_1
2/16/2016 15:24:41 PM
PMR446MR-2CK
*Range may vary depending on environmental and/or topographical conditions.
• 8 PMR Channels
• 121 Sub Codes
(CTCSS Tone and DCS Code)
• Up to 8 Km Range*
• Internal VOX Circuitry
• 10 Selectable Call Tone Alerts
• Backlit LCD Display
• Optional Headset Accessories
• Headset Jack
1 Antenna
2 PTT (Push-To-Talk) Button
3
Monitor Key
4
Channel Up/Down key
5
Call/Lock Button
6
Headset Jack/
7
DC IN 9V
8
Menu/Power key
9 Volume Up/Down key
10 Microphone
11
Speaker
12
Battery Level Meter
13
Receive Indicator
14
Call Indicator
15
Scan Indicator
16 Transmit Indicator
17 Volume Setting Indicator
18 Keypad Lock Indicator
19 VOX Indicator
20
Channel Indicator
21
Sub Code Indicator
Charging Contacts
This lightweight, palm-sized, radio is a
state-of-the-art device, equipped with many
valuable features.
Use it at sporting events, to stay in contact with
family and friends, hiking, skiing, outdoors, or in
a neighborhood watch for vital communication.
PACKAGE CONTENTS
Your package contains:
Two radios
Two rechargeable NiMH battery packs
One AC adapter EU/UK
One dual charging cradle
Two belt clips
This reference guide
INSTALL THE BATTERY
Your radio uses a supplied NiMH battery pack.
To install the NiMH battery pack:
1) Make sure your radio is OFF.
2) Release the battery latch at the bottom of the
radio, and remove the cover.
3) Install the NiMH battery pack into the battery
compartment. Be certain to follow the
instructions written on the label on the battery
pack. Installing the battery pack incorrectly will
prevent the unit from operating.
4) Before placing the battery cover back on the
radio, check the rubber seal around the battery
compartment and the ribbon of the battery pack:
make sure that the seal is in good condition and
that there is no foreign matter under the seal.
5) Replace the battery compartment cover.
USING THE RADIO
•
•
•
•
•
•
•
Roger Beep
• Battery Charger
• Battery Level Meter
• Channel Monitor
• Channel Scan
• Keypad Lock
• DC IN 9V Jack
BATTERY LEVEL AND LOW BATTERY
ALERT
This unit has a battery level meter on the display to
indicate the status of the batteries. When the
battery in the unit is low, the battery level meter
icon
flashes. Recharge the NiMH battery
pack immediately.
Warning!
To avoid the risk of personal injury or
property damage from fire or electrical shock, only
use the accessories specifically designated for this
product.
PMR446MR-2CK RADIO
CHARGING THE RADIO
• For fastest charging, turn off the radio before
charging.
• Battery must be installed for operation, even from
external power.
• If battery power is low, you cannot operate the
radio even using external power. Allow the
batteries to charge before using. If you try to
transmit while power is low, the radio will
automatically turn off.
USING A HEADSET
You can use an optional headset accessory for more
private communications.
To use a headset, lift the rubber cover from over
the headset jack, then plug in the headset.
Your radio can be charged directly or by using the
supplied charging cradle.
Make sure to turn the radio OFF before placing
the radio in the charging cradle.
Charge by Using the 12V DC Cable
1) Connect the optional DC adapter to DC IN 9V
jack of the radio and to a cigarette lighter port.
2) Charge the battery pack for 16 hours until the
battery indicator stops flashing.
Note:
• DC IN 9V Jack of the radio is for charge only.
Be sure to install the battery before charge.
• Use only the supplied battery and AC adapter or
approved accessories.
• Charge time may vary depending on the battery
life remaining.
In order to get the most out of your new radio, read
this reference guide completely before attempting to
operate the unit.
Turning the Radio On and Adjusting the Volume
1) Press and hold the
MENU/
key to turn the
radio ON, and increase the speaker volume by
pressing the
VOL
key. To decrease the volume,
press the
VOL
key.
2) Press and hold the
MENU/
key again to turn
the radio OFF.
Adjusting the Sound (Key Beeps)
Your radio emits a beep each time one of the keys
(except for the
PTT
button and
CALL
key) is
pressed.
To turn this sound OFF, press and hold
CALL/LOCK
while turning ON the radio.
Repeat this step to turn the sound ON.
Choosing a Channel
Your radio has 8 channels and 121 Sub codes you
can use to talk to others. In order to speak to
someone, each of you must be set to the same
channel and Sub code.
To choose a channel:
Choosing a Sub Code
Each of the channels 1-8 may have any one of
the codes, OFF or 1-121 selected. Code
oF
(OFF)
indicates no Sub code selected and your radio can
receive a signal regardless of the code settings of
the transmitting radio.
1) Press
MENU/
key.
2) Press the
CH
or key to increase or
decrease the code number displayed. You can
also select
oF
(OFF) at this stage.
3) Press
MENU/
key.
With the radio in "Normal" operating mode, press
the
CH
or
key to increase or decrease the
channel number displayed.
Channel Scan Feature
Your radio has a channel scan feature that allows
you to easily scan all 8 channels. When an active
channel is detected, the radio pauses on that
channel until the channel is clear. Then, after a 2
second delay, the radio continues scanning.
To turn ON channel scan:
Press
MENU/
key twice. The
scan...
icon and
oF
(OFF) blink. Press
CH
key to select on, and then
press
MENU/
key. The channel number changes as
the radio rapidly cycles through the channels.
To turn OFF channel scan:
Press the
CALL/LOCK
,
PTT
,
MENU/
key.
Congratulations on your purchase of the PMR446.
Contact your dealer for a headset with correct
jack/wiring.
Pressing the
PTT
button will stop the Channel Scan
Feature.
Using the Charging Cradle
1) Connect the AC adapter to DC IN 9V jack and to
a standard AC wall outlet.
2) Set the charging cradle on the desk or tabletop,
and place the radio in the charging cradle with
the keypad facing forward.
3) Make sure that the LED illuminates. Charge the
battery pack for 16 hours and remove the radio
from the charging cradle after charging.
CHARGE
