background image

PAGE 1 OF 18 

0623 IH-7935

ALL-WEATHER  

LOW PROFILE

FLOOR SCALE

1-800-295-5510

uline.com

H-7935, H-7936, H-9672 

H-9673, H-10903, H-10904

INTRODUCTION
INTRODUCTION

SITE SELECTION 

Select a site for the floor scale where it is least likely to 

be damaged by forklifts and other material handling 

devices. Floor scale load cell weighing elements are 

prone to overload damage caused by side impacts, 

falling objects and weight loads that exceed the rated 

capacity of the scale. 

Site should be:

• Level within 1/4".

• Free from vibration.

• Clean of debris.

•  Out of the way of vehicle traffic patterns, unless 

installed in a pit while having a rated capacity 

that exceeds all loaded vehicle weights that could 

possibly drive onto or contact the scale.

The cable from the floor scale to the digital weight 

indicator should be run through conduit to protect it 

against possible damage. Running the instrument cable 

through conduit is the best method of protection.

UNPACKING

1.  Inspect your shipment for damage. If you see visible 

signs of damage, notify carrier at once.

2.  Remove floor scale from the shipping pallet. 

3.  Unpack the digital indicator. Digital indicator and 

power cord ship in a separate box.

RAMP INSTALLATION (OPTIONAL)

1.  Set floor scale in a desired location.

2.  Position the scale feet inside the mounting tabs.  

(See Figure 1)

3.  Anchor the ramp to the floor using two 1/2 x 3" 

anchors (not included).

HEIGHT AND LEVEL ADJUSTMENTS

1.  Unlock the locknuts on all four feet.

2.  Using a pry bar, lift the weight of the scale base off 

the scale feet.

3.  Make adjustments by screwing the feet 

counterclockwise. All four feet should make firm 

contact with the floor.

4.  Do not screw feet counterclockwise more than ten 

turns.

5.  Tighten locknuts on feet.

6.  Check your work.

Para Español, vea páginas 7-12.

Pour le français, consulter les pages 13-18.

Figure 1

Ramp

Scale

Mounting Tabs

Load Cell Foot

Anchor goes here.

Summary of Contents for H-10903



















Reviews: