background image

INSTALLATION 

AND 

OPERATING 

INSTRUCTIONS

 

 

 

 
 

 

 

Gas Griddles 

MODELS: TSGGT-18i, -24i, -36i, -48i  

MODELS: TSGGM-18i, -24i, -36i, 48i 

(US & Canadian units are convertible and are assembled for Natural Gas) 

(European units are not convertible and assembled for the appropriate gas) 

 

IMPORTANT FOR FUTURE REFERENCE 

 

Please complete this information and retain this manual for the life of the equipment. For Warranty 
Service and/or Parts, this information is required. 

 

 

Model Number 

 

Serial Number 

 

Date Purchased 

 

 
 

FOR YOUR SAFETY:

 Do not store or use gasoline or other flammable vapors and liquids 

in the vicinity of this or any other appliance. 

 

 

 

WARNING:

  Improper  installation,  operation,  service  or  maintenance  can  cause  property 

damage,  injury  or  death.  Read  and  understand  these  instructions  thoroughly  before 
positioning, installing, maintaining or servicing this equipment. 

 

P/N 882213, REV 9/13 

TRI-STAR MANUFACTURING 

 

DALLAS: 

CHEYENNE: 

1307 N. Watters Rd #180 

 Allen, TX 

 75013 

1938 Wyott Dr 

 Cheyenne, WY 

 82007 

Local: (972) 908-6100 

Local: (307) 634-5801 

Toll Free: (800) 733-2203 

Toll Free: (800) 752-0863 

Parts/Service Fax: (214) 565-0976 

Parts/Service Fax: (214) 565-0976 

 

www.tri-starmfg.com 

Summary of Contents for TSGGM-18i

















Reviews: