background image

Models:

TCH024C1

TCH042C1

TCH030C1

TCH048F1

TCH036C1

TCH060F1

Packaged Cooling
Electric Heat
Over/Under
2, 2-1/2, 3, 3-1/2, 4, 5 Tons

TCH-IOM-10

18-AB33D6-10

IMPORTANT — 

This Document is customer property and is to remain with this unit.  Please return to service information pack upon completion of work.

©  2009 Trane

The manufactuter has a policy of continuous product and product data improvement, and it reserves the right to change design and
specification without notice.

INSTALLATION
OPERATION
MAINTENANCE

THIS INFORMATION IS FOR USE BY INDIVIDUALS HAVING
ADEQUATE BACKGROUNDS OF ELECTRICAL AND MECHANI-
CAL EXPERIENCE.  ANY ATTEMPT TO REPAIR A CENTRAL
AIR CONDITIONING PRODUCT MAY RESULT IN PERSONAL
INJURY AND/OR PROPERTY DAMAGE.  THE MANUFACTURER
OR SELLER CANNOT BE RESPONSIBLE FOR THE INTERPRE-
TATION OF THIS INFORMATION, NOR CAN IT ASSUME ANY
LIABILITY IN CONNECTION WITH ITS USE.

 

Reconnect all grounding devices.

All parts of this product that are capable of conducting electri-
cal current are grounded.  If grounding wires, screws, straps,
clips, nuts, or washers used to complete a path to ground are
removed for service, they must be returned to their original
position and properly fastened.

ALL phases of this installation must comply with NATIONAL,
STATE, and LOCAL CODES.

These instructions do not purport to cover all variations in
systems nor to provide for every possible contingency to be
met in connection with installation.

  Should further information be

desired or necessary or should particular problems arise which are
not covered sufficiently for the purchaser's or installer's needs or
purposes, the matter should be referred to the manufacturer.

 

HAZARDOUS VOLTAGE - DISCONNECT POWER BEFORE SERVICING

WARNING:

CAUTION

!

WARNING

!

CAUTION

!

CONTAINS REFRIGERANT!
SYSTEM CONTAINS OIL AND REFRIGERANT UNDER
HIGH PRESURE. RECOVER REFRIGERANT TO RELIEVE
PRESSURE BEFORE OPENING SYSTEM

. Failure to follow

proper procedures can result in personal illness or injury or
severe equipment damage.

04/09

2, 2-1/2, 3, 3-1/2 Tons Shown

Summary of Contents for TCH024C1













Reviews: