®
PART #776
READ ALL WARNINGS AND INSTRUCTIONS BEFORE INSTALLATION
WARNING:
AT NO TIME SHOULD THE MAXIMUM WORKING LOAD OF THE MANUAL TOWING WINCH BE EXCEEDED. THE MAXIMUM WORKING
LOAD IS 1,500LB (680KG) MAX CAPACITY.
WARNING:
BEFORE EACH USE, INSPECT MANUAL WINCH, WEBBING, AND MOUNTING TO ENSURE PROPER ASSEMBLY AND FOR ANY
DAMAGE. IF ANY PART IS DAMAGED, DO NOT USE. REPLACE COMPONENTS IMMEDIATELY.
WARNING
: DO NOT USE STRAP IF WORN, FRAYED, OR DAMAGED IN ANY WAY. BREAKING OF STRAP COULD CAUSE SERIOUS DAMAGE TO
SURROUNDING AREAS, SERIOUS INJURY, AND/OR DEATH.
WARNING
: DO NOT USE HANDS TO GUIDE STRAP OF MANUAL WINCH. USE CLEAN HANDS WHEN OPERATING WINCH.
WARNING:
ALWAYS LEAVE THREE (3) LAYERS OF STRAP AROUND THE WINCH AXLE.
WARNING
: BEFORE CRANKING THE HANDLE, ENSURE RATCHET PAWL IS ENGAGED. IF TWO HANDS ARE NEEDED TO CRANK, MAX CAPACITY
OF WINCH MAY BE OVERLOADED.
WARNING:
CHECK MANUAL WINCH BEFORE, DURING, AND AFTER MOUNTING AND USE. CHECK THE WINCH AND MOUNTING HARDWARE
REGULARLY. IT IS RECOMMENDED TO CHECK AFTER THE FIRST TEN (10) MILES (16KM) AFTER INSTALLATION.
FIGURE 1
FIGURE 2
FIGURE 3
INSTALLATION:
1. ASSEMBLE WINCH HANDLE AS SHOWN IN FIGURE 1. TIGHTEN LOCKING NUT TO A TORQUE OF 25 FT-LBS. DO NO OVER TORQUE.
2. SLIP THE LOOP ON THE STRAP THROUGH THE STRAP CROSS BOLT, SHOWN IN FIGURE 2. TIGHTEN STRAP CROSS BOLT WITH PROVIDED
NUT. TORQUE TO 10FT-LBS. (14N-M). TORQUING ABOVE THIS COULD RESULT IN THE WINCH BENDING AND CAUSE IT TO FAIL BELOW
CAPACITY. CHECK TO ENSURE WINCH SPINS FREELY BY HAND.
REMEMBER:
ALWAYS LEAVE THREE (3) LAYERS OF STRAP AROUND THE AXLE.
FIGURE 3 SHOWS THE WINCH FULLY ASSEMBLED.
3. SUGGESTED MOUNTING HARDWARE: 3/8” DIAMETER, GRADE-5 HARDWARE (BOLTS AND LOCKNUT OR LOCKWASHER AND NUT). USE AT
MINIMUM THREE (3) OF EACH. TORQUE TO 30FT-LBS. (41N-M). CHECK MOUNTING HARDWARE BEFORE INSTALLATION. TIGHTEN TO PROPER
TORQUE RATING.
WARNING:
DO NOT LUBRICATE DURING INSTALLATION. LUBRICATION COULD ALLOW FOR TORQUE TO EXCEED LIMITATIONS AND CAUSE
PRODUCT TO FAIL. PROPER MOUNTING INSTALLATION IS CRITICAL FOR WINCH TO REACH MAXIMUM CAPCITY RATING.
***NOTE: FIRMLY HOLD ONTO THE WINCH HANDLE BEFORE MOVING THE POSITION OF THE RATCHET PAWL.***
THE ATTACHMENT AND INSTALLATION OF THIS PRODUCT IS CRITICAL AND BEYOND THE CONTROL OF WINSTON PRODUCTS, LLC. WINSTON
PRODUCTS, LLC IS NOT RESPONSIBLE FOR ANY DAMAGE THAT COULD RESULT FROM IMPROPER USE, INSTALLATION, OR ATTACHMENT. AT
NO TIME SHOULD THE SAFE WORKING LOAD OF THIS PRODUCT BE EXCEEDED.
MANUAL TOWING WINCH
INSTALLATION INSTRUCTIONS
INSTRUCCIONES DE INSTALACION
CONSIGNES D’ INSTALLATION
LEA TODAS LAS ADVERTENCIAS E INSTRUCCIONES ANTES DE LA INSTALACIÓN
ADVERTENCIA:
EN NINGÚN MOMENTO SE DEBE EXCEDER LA CARGA MÁXIMA DE TRABAJO DEL CABRESTANTE MANUAL. LA CARGA MÁXIMA
DE TRABAJO ES 1,500 LB (680 KG), CAPACIDAD MÁXIMA.
ADVERTENCIA:
INSPECCIONE EL CABRESTANTE MANUAL, LA CORREA Y LA MONTURA ANTES DE CADA USO, PARA ASEGURAR EL MONTAJE
ADECUADO Y PARA EVITAR CUALQUIER
DAÑO. SI ALGUNA PIEZA ESTÁ DAÑADA, NO LO USE. REEMPLACE LAS PIEZAS INMEDIATAMENTE.
ADVERTENCIA:
DE NINGUNA MANERA UTILICE LA CORREA SI ESTÁ GASTADA, RASGADA O DAÑADA. EL ROMPIMIENTO DE LA CORREA PO-
DRÍA CAUSAR DAÑOS GRAVES EN LAS ZONAS CIRCUNDANTES, LESIONES GRAVES O LA MUERTE.
ADVERTENCIA:
NO USE LAS MANOS PARA ENCARRILAR LA CORREA DEL CABRESTANTE MANUAL. TENGA LAS MANOS LIMPIAS CUANDO
UTILICE EL CABRESTANTE.
ADVERTENCIA:
SIEMPRE DEJE LAS TRES (3) CAPAS DE LA CORREA ALREDEDOR DEL EJE DEL CABRESTANTE.
ADVERTENCIA:
ANTES DE MANIPULAR LA PALANCA DE MANO, ASEGÚRESE DE QUE EL TRINQUETE ESTÉ ENCAJADO. SI SE NECESITAN DOS
MANOS PARA GIRAR LA PALANCA, LA CAPACIDAD MÁXIMA DEL CABRESTANTE PUEDE ESTAR SOBRECARGADA.
ADVERTENCIA:
REVISE EL CABRESTANTE MANUAL ANTES, DURANTE Y DESPUÉS DEL MONTAJE Y USO. REVISE EL CABRESTANTE Y LAS
HERRAMIENTAS DE MONTAJE REGULARMENTE. SE RECOMIENDA REVISAR DESPUÉS DE LAS PRIMERAS DIEZ (10) MILLAS (16 KM) DESPUÉS
DE LA INSTALACIÓN.
