background image

WARRANTY

TOWER HOBBIES

®

guarantees this kit to be free from defects in both material and workmanship at the date of purchase. This warranty

does not cover any component parts damaged by use or modification. In no case shall TOWER HOBBIES' liability exceed the
original cost of the purchased kit. 
Further, TOWER HOBBIES reserves the right to change or modify this warranty without notice.

In that TOWER HOBBIES has no control over the final assembly or material used for final assembly, no liability shall be assumed nor
accepted for any damage resulting from the use by the user of the final user-assembled product. By the act of using the user-assembled
product, the user accepts all resulting liability.

If the buyer is not prepared to accept the liability associated with the use of this product, the buyer is advised to return this
kit immediately in new and unused condition to the place of purchase.

To make a warranty claim send the defective part or item to Hobby Services at the address below:

Hobby Services

3002 N. Apollo Dr., Suite 1

Champaign, IL 61822

USA

Include a letter stating your name, return shipping address, as much contact information as possible (daytime telephone number, fax
number, e-mail address), a detailed description of the problem and a photocopy of the purchase receipt. Upon receipt of the package
the problem will be evaluated as quickly as possible.

READ THROUGH THIS MANUAL BEFORE STARTING CONSTRUCTION. IT CONTAINS IMPORTANT
INSTRUCTIONS AND WARNINGS CONCERNING THE ASSEMBLY AND USE OF THIS MODEL.

Entire Contents © Copyright 2006  V1.0

TOWZ0004 for TOWA4015

TOWER HOBBIES

P.O. Box 9078

Champaign, IL 61826

(800) 637-6050

www.towerhobbies.com

Wingspan: 78.5 in [2000mm]

Wing Area: 678 sq in [43.7dm

2

Weight: 45 – 50 oz [1275 – 1415g] 

Wing Loading: 9.6 – 10.6 oz/sq ft [29 – 32g/dm

2

Length: 41 in [1035mm] 

Motor: Included 550

Radio: Three-channel, two standard servos

Summary of Contents for Vista EP

















Reviews: