background image

INSTRUCTION

MANUAL

READ THROUGH THIS MANUAL

BEFORE STARTING CONSTRUCTION.

IT CONTAINS IMPORTANT INSTRUCTIONS 

AND WARNINGS CONCERNING THE 

ASSEMBLY AND USE OF THIS MODEL.

WINGSPAN

40 in [1016 mm]

WING AREA

303 in

2

 [15.2 dm

2

]

WEIGHT

29.7–32 oz [840–905 g]

WING LOADING

14.1–15.2 oz/ft

2

 [43–46 g/dm

2

]

LENGTH

34 in [864 mm]

RADIO

4-Channel minimum required

To w e r 
Hobbies

®

 

guarantees 
this kit to be 
free from defects 
in both material and 
workmanship at the 
date of purchase. This 
warranty does not cover any 
component parts damaged by 
use or modification. In no case 
shall Tower Hobbies’ liability exceed 
the original cost of the purchased kit. 
Further, Tower Hobbies reserves the right to 
change or modify this warranty without notice.
In that Tower Hobbies has no control over the final 
assembly or material used for final assembly, no 
liability shall be assumed nor accepted for any damage 
resulting from the use by the user of the final user- 
assembled product. By the act of using the user-assembled 
product, the user accepts all resulting liability.
If the buyer is not prepared to accept the liability associated with the 
use of this product, the buyer is advised to return this kit immediately in 
new and unused condition to the place of purchase.
To make a warranty claim send the defective part or item to Hobby Services at 
the address below:

(OBBY3ERVICESs.!POLLO$R3UITEs#HAMPAIGN),s53!

Include a letter stating your name, return shipping address, as much contact information 
as possible (daytime telephone number, fax number, e-mail address), a detailed description 

OF THE PROBLEM AND A PHOTOCOPY OF THE PURCHASE RECEIPT 5PON RECEIPT OF THE PACKAGE THE

problem will be evaluated as quickly as possible.

WA

R

R

A

N

T

Y

TOWA2000 Mnl 1.1 

©2010 Tower Hobbies

®

®

®

TOWER HOBBIES

Champaign, Illinois

 (217) 398-8970 ext. 5

Содержание P-51D Mustang













Отзывы: