TJERNLUND SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198 Installation Instructions Manual Download | Manualshive

Page: 1 / 14

background image

Copyright © 1998, Tjernlund Products, Inc. All rights reserved

P/N 8504075

OWNER INSTRUCTIONS, DO NOT DESTROY

Recognize this symbol as an indication of important safety information!

NOTE: MAXIMUM FLUE GAS TEMPERATURES MUST NOT EXCEED 650oF.

THESE INSTRUCTIONS ARE INTENDED AS AN AID TO QUALIFIED, LICENSED SERVICE
PERSONNEL FOR PROPER INSTALLATION, ADJUSTMENT AND OPERATION OF THIS
UNIT. READ THESE INSTRUCTIONS THOROUGHLY BEFORE ATTEMPTING INSTALLA-
TION OR OPERATION. FAILURE TO FOLLOW THESE INSTRUCTIONS MAY RESULT IN
IMPROPER INSTALLATION, ADJUSTMENT, SERVICE OR MAINTENANCE POSSIBLY
RESULTING IN FIRE, ELECTRICAL SHOCK, CARBON MONOXIDE POISONING, EXPLO-
SION, PERSONAL INJURY OR PROPERTY DAMAGE.

!

DO NOT DESTROY. PLEASE READ CAREFULLY AND

KEEP IN A SAFE PLACE FOR FUTURE REFERENCE.

MODEL SS2G

INSTALLATION INSTRUCTIONS

REV. 1 11/98

56826

TJERNLUND PRODUCTS, INC.

1601 Ninth Street • White Bear Lake, MN 55110-6794
PHONE (800) 255-4208 • (651) 426-2993 • FAX (651) 426-9547
Visit our web site • www.tjernlund.com

1
2
3
...
»

Summary of Contents for SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198















Reviews:

No comments

Related manuals for SS2G SIDESHOT (DISCONTINUED) 8504075 REV 1 1198

Brand: Daewoo Pages: 205

SEL Plus-RC Series

Brand: Selve Pages: 172

Vanguard 540000 Series

Brand: Briggs & Stratton Pages: 32

Brand: Westerbeke Pages: 140

Brand: YOODA Pages: 7

Brand: Amico Pages: 47

Brand: Kohler Pages: 160

3T-MOTORS 3T45-10E

Brand: 3T-Components Pages: 12

3T-MOTORS 3T35-13

Brand: 3T-Components Pages: 24

3T-MOTORS 3T35-10SD

Brand: 3T-Components Pages: 16

3T-MOTORS 3T35-10R

Brand: 3T-Components Pages: 20

Brand: Stark Pages: 14

Brand: aFe Power Pages: 16

Brand: Volvo Pages: 64

Brand: Panther Pages: 7

BEVELMASTER 204B

Brand: TRI tool Pages: 46

Brand: O.S. engine Pages: 38

Brand: MVVS Pages: 12

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands