thermastor Quest 335 Installation, Operation And Maintenance Instructions Download | Manualshive

Page: 1 / 24

background image

Quest 335

Installation, Operation and Maintenance Instructions

– Read and Save These Instructions –

This manual is provided to acquaint you with the

dehumidifer so that installation, operation and

maintenance can proceed successfully. Ultimate

satisfaction depends on the quality of installation and a

thorough understanding of this equipment. The dehumidifer

is built around tested engineering principles and has passed

a thorough inspection for quality of workmanship and

function.

Patent: thermastor.com/patents

Features:
•  208V and 230V 60Hz
•  Industry-leading efficiency
•  Patented, multi-coil refrigeration system
•  High-efficiency, variable-speed impeller
•  Quiet operation
•  Superior air filtration (MERV-13 standard)
•  Auto-restart after loss of power
•  Environmentally friendly R410A refrigerant
•  Low voltage external control
•  On-Board digital controls

Water Removal Rates (Pints/Day) @ 80°F 60% (RH)

Dehumidifier
335

Pints Removed

335

Gallons/Liters

42/158

4201 Lien Rd

Madison, WI 53704

www.QuestClimate.com

Toll-Free 1-877-420-1330

[email protected]

Specifcations subject to change without notice.

1

TS-1196

09/21 Rev. A

1
2
3
...
»

Summary of Contents for Quest 335

























Reviews:

No comments

Related manuals for Quest 335

Brand: Salter Labs Pages: 2

Brand: S&P Pages: 18

Brand: UCAN Pages: 20

Brand: SOLAC Pages: 4

Airtek SMART CYCLE PLUS 80

Brand: Parker Pages: 45

Brand: Ariston Pages: 60

Brand: Woods Pages: 4

Brand: Holmes Pages: 2

Ultrasonic Humidifier

Brand: Vornado Pages: 11

REFLECTION HUL900 Series

Brand: Honeywell Pages: 17

Brand: Honeywell Pages: 18

REFLECTION HUL900BC

Brand: Honeywell Pages: 29

Brand: Honeywell Pages: 52

TRADELINE HE360

Brand: Honeywell Pages: 40

HWM 335 - 3G Warm Humidifier

Brand: Honeywell Pages: 44

Brand: Honeywell Pages: 32

Brand: Honeywell Pages: 60

Brand: Honeywell Pages: 29

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands