ALARM SETTING
The maximum alarm duration is 80 seconds. To set the alarm function:
1.
Press the ALM key for about 1 second or until the digits start flashing in the LCD to enter into the
Alarm setting mode. The hour digits start flashing.
2.
Press the + key to set the hour.
3.
Press the ALM key to enter the minute mode. The minute digits start flashing.
4.
Press the + key to set the minutes.
5.
Press the ALM key or the SNOOZE key to exit the Alarm setting mode or wait for 15 seconds
automatic timout.
Note:
If the ALM key is pressed for a short time, the alarm toggles between ON/OFF. At the same time, the
current alarm time will be displayed for about 4 seconds.
TO ACTIVATE / DEACTIVATE THE ALARM:
The alarm will automatically be ON upon entering and exiting the Alarm setting mode. To desactivate
the alarm (OFF), use the ALM key in normal mode display.
SNOOZE SETTING
•
When pressing the SNOOZE key during alarm sounding, the snooze function is activated for a
duration of 9 full minutes.
•
When keeping the SNOOZE key during alarm sounding for 1 second, after confirmation of a
"beep“ sound, the alarm will switch OFF for the next 24 hours and no snooze function will be
activated.
Note:
If the SNOOZE key is pressed for about 1 second, except during alarm ringing, it will display the alarm
time for about 4 seconds.
POSITIONING THE MOON PHASE CLOCK
The Moon Phase Clock can be either free standing or hanging on a wall:
To free stand
:
Simply unfold the 2 stands at the back of the clock and place on a flat surface.
To wall mount
:
1.
Fix a screw into the desired wall, leaving the head extended out by about 5mm
2.
Using the Moon Phase Clock‘s hanging hole, carefully hang it onto the screw.
Note:
Always ensure that the Moon Phase Clock locks onto the screw before releasing.
CARE AND MAINTENANCE
•
Avoid placing the unit in areas prone to vibration and shock as these may cause damage.
•
Avoid areas where the unit can be exposed to sudden changes in temperature, i.e. direct sunlight,
extreme cold and wet/moist conditions as these will lead to rapid changes which reduces the
accuracy of readings.
•
When cleaning the LCD and casing, use a soft damp cloth only. Do not use solvents or scouring
agents.
•
Do not submerge the unit into water.
•
Immediately remove all low powered batteries to avoid leakage and damage. Replace only with
new batteries of the recommended size.
•
Do not make any repairs to the unit. Please return it to the original point of purchase for repair by a
qualified engineer. Opening and tampering with the unit may invalidate its guarantee.
SPECIFICATIONS
Indoor temperature measuring range :
0ºC to +50ºC with 0.1ºC resolution
32ºF to +122ºF with 0.2ºF resolution
("--.-" displayed if outside this range)
Indoor temperature checking interval :
every 10 seconds
Power source
:
2 x AA, IEC LR6, 1,5V batteries
(Alkaline batteries recommended)
Battery life
:
about 12 months
Dimensions (L x W x H)
:
290 x 25 x 190mm
LIABILITY DISCLAIMER
•
The manufacturer and supplier cannot accept any responsibility for any incorrect readings and any
consequences that occur should an inaccurate reading take place.
•
This product is only designed for use in the home
•
This product is not to be used for medical purposes or for public information.
•
The specifications of this product may change without prior notice.
•
This product is not a toy. Keep out of the reach of children
•
No part of this manual may be reproduced without written authorization of the manufacturer.
R&TTE Directive 1999/5/EC
To be used in EC Member and EFTA States.
Summary of the Declaration of Conformity : We hereby declare that this wireless transmission device
does comply with the essential requirements of R&TTE Directive 1999/5/EC.
