Teknic E3PS12-75 Power Supply Quick Reference
Teknic model E3PS12-75 is a 75 VDC intelligent power supply
designed to provide the same reliable power and performance as its
predecessor (3PS12-75) with several added capabilities:
●
Drop-in compatibility with Teknic SSt-3PS12-75.
●
115 VAC or 230 VAC
*
nominal input voltage.
●
Automatic DC bus dump on power down.
●
Easy adjustment for high, medium or low AC line voltage.
●
Intelligent regenerative energy management.
●
Embedded microcontroller.
Introduction
E3PS12-75 Parts
Fuses (x2)
(see below)
DC Output
Connector
AC Input
Connector
Input Voltage
Selector Switch
Status LED
P1
P3
Mounting Hole (x4)
Mounting
Bracket
Circuit Board
Main Capacitor
Transformer
(behind main cap)
The E3PS12-75 should be installed and operated as specified herein.
Failure to do so may impair or defeat any protections provided by the
equipment. Please read and follow all instructions before installing or
operating this device.
General Safety
The power supply should be mounted behind covers or machine skins
that can only be opened with a tool. The covers or machine skins
should be marked as having hazardous voltages within. Alternatively,
the supply can be mounted behind doors that have a safety interlock
that removes power to the supply when opened.
The power supply should not be mounted in an area where the
ambient temperature exceeds 40°C.
Mounting Safety
Replacement Fuses
Description: Fuse, 3AB, 2A, slow blow, 250VAC
Cooper Bussman MDQ-2
Important:
Use only
the fuse type listed above
regardless of AC line
voltage used
. Using the wrong fuse can damage the power supply,
create a fire hazard, cause nuisance circuit breaker trips, and void the
product warranty.
Rev. M 09/14/15
ANNII
BII
TII
JL
RH
HV
AS
JW
Note: Teknic does not supply or sell 230VAC power cables for this
product. Users operating at 230VAC must build or otherwise source
this cable. Cable pinout can be found under “Mating Connectors” at right.
*
Housing: Molex/39-01-2100
Terminals: Molex/39-00-0059
Crimp Tool: Molex/638190900
Extractor Tool: Molex/11-03-0044
Cable: 18AWG, 300V, Stranded
Housing: Molex/44441-2002
Terminals: Molex/43375-0001
Crimp Tool: Molex/63811-7200
Cable: 14-16AWG, 600V, Stranded
Mating Connectors
AC Input Connector / Pinout
DC Output Connector / Pinout
1
2
3
4
10
5
7
8
9
6
Pos. 115 VAC
230 VAC*
no connect
no connect
AC IN
no connect
AC IN
GND
no connect
no connect
Jump to 9
Jump to 7
no connect
no connect
Jump to 9
no connect
Jump to 7
GND
AC IN
AC IN
Jump to 10
Jump to 6
1
2
Pos.
Signal
DC Bus (V+)
DC Bus (V-)
1
10
5
6
1
2
wire entry view
wire entry view
Note: Teknic does not supply or sell
a 230VAC input cable for this product.
Mounting Dimensions
inch (mm)
Note:
screw head protrudes.09” from
projected surface. This does not affect
standard mounting surface.
7.786
(197.76)
4.100
(104.14)
7.155
(181.74)
0
0.255
(6.48)
.300
(7.62)
4.050
(102.87)
4.964
(126.09)
8.087
(205.41)
All Mounting holes
0.25” dia. thru +/- .02”
0.090
(2.29)
0
0
8.1”
3.9”
5.0”
