TECO JSDE Series Manual Download

Page: 1 / 62

■

Warning and Alert:

Warning

Do not proceed to the assembly of the line while electrifying.

Before doing any maintenance or repair always wait until CHARGE LED goes off and supply
power is totally separation from the drive.

The output terminal of Servo drive [U, V, W] must NOT touch the AC power.

Alert

Install the cooling fan for the Servo drive while the environment temperature is too high.

Ex. Servo driver is installed in the control panel.

Do not proceed to the Anti-Pressure-Test to the Servo driver.

Confirm the quick stop function is available before operate servo drive.

Matching up machine to change the user parameter setting before machine performs. If there is

no according correct setting number, it could lead to out of control or breakdown.

Safety proceeding:

Check the covering letter detail before installing, running, maintaining and examining. Furthermore, only

the profession-technician can proceed to assemble and repair.

Safety proceeding in the covering letter discriminate between “Warning” & ”Alert”.

Indicating the possibility dangerous situation. It could cause the death or serious

damage if being ignored.

Indicating the possibility dangerous situation. It could cause smaller or lighter human

injured and damage of equipment

Read this covering letter detail before using Servo driver.

Alarm

Warning

Summary of Contents for JSDE Series































































Search results

Summary of Contents for JSDE Series

Reviews:

Related manuals for JSDE Series

Brands by name

Popular brands

TECO JSDE Series, Manual

Search results

Summary of Contents for JSDE Series

Reviews:

Related manuals for JSDE Series

Brands by name

Popular brands