background image

POINT TYPE FLAME DETECTOR  

"ALMAZ"

 

 

 
 

 

 

 

 

 

 
 

PASSPORT 

APKI 412216.001 PS 

 

 

 

 
 

TECHNOTRADE LTD 

POINT TYPE FLAME DETECTOR "ALMAZ" 

www.technotrade.ua

 

                                                                                               Page 2 of 27 

 

CONTENT 

 

 

1. INTRODUCTION ..................................................................................................... 3 
2. FUNCTION ............................................................................................................. 3 
3. TECHNICAL SPECIFICATIONS ................................................................................. 4 
4. PRODUCT SET CONTENTS ..................................................................................... 5 
5. DEVICE AND ITS OPERATION PRINCIPLE ............................................................... 6 
6. SAFETY REQUIREMENTS ....................................................................................... 7 
7. INSTALLATION AND MOUNTING........................................................................... 8 
8. TECHNICAL MAINTENANCE................................................................................. 10 
9. POSSIBLE MALFUNCTIONS AND TROUBLESHOOTING ........................................ 12 
10. HANDLING AND STORAGE ................................................................................ 13 
11. CERTIFICATE OF ACCEPTANCE .......................................................................... 14 
12. MANUFACTURER WARRANTY ........................................................................... 14 
APPENDIX A ............................................................................................................. 15 
APPENDIX B ............................................................................................................. 17 
APPENDIX C ............................................................................................................. 18 
APPENDIX D ............................................................................................................ 19 
APPENDIX E ............................................................................................................. 20 
APPENDIX F ............................................................................................................. 21 
APPENDIX G ............................................................................................................ 26 
APPENDIX H ............................................................................................................ 27 

 
 
 
 

 
 
 
 

 
 
 

Summary of Contents for ALMAZ















Reviews: