![background image](http://html1.mh-extra.com/html/technexion/axon-pi-imx8m-mini/axon-pi-imx8m-mini_quick-start-manual_1067210001.webp)
3.1
Connect the parts
3.2
WiFi antenna
3.3
Camera module (opional)
AXON-PI-IMX8M-MINI
Quickstart Guide
3
Installaion Instrucions
This installaion guide will help you to assemble your development kit using step-by-step instrucions to make sure all parts (development board, WiFi antenna, camera
module and display) are working.
Please follow the steps below to properly install the WiFi antenna.
Step 1: Prepare WiFi antenna, extender cable and development board.
Step 2: Locate the round antenna pin on the development board. Make sure the connector is aligned with the pin. Press the small round connector at the end of the
extender cable onto this pin. You will need to press down unil you hear a click sound.
Step 3: Screw the extender cable into the base of the WiFi antenna.
Connect the parts in the following order. Please note that some versions of the AXON-PI-IMX8M-MINI evaluaion kit do not include the camera, muli-touch display,
and/or cardboard stand.
Tips: Do not power your board during the installaion process.
Please follow the steps below to properly install the camera module.
Step 1: Prepare camera module, FPC cable and evaluaion board. Turn the camera module over to reveal a white connector near the edge of the module.
Step 2: Swivel the black retaining clip upward.
Step 3: Insert either end of the camera module cable into the white connector. Make sure that the blue side of the ribbon is facing up and is aligned straight with the
connector. The silver pins on the FPC cable should be facing down.
Step 4: Swivel the retaining clip back down to hold the FPC cable in place.
Steps 5 and 6: Repeat these same steps with the other end of the cable and the connector on the board.
Tips: Ater installaion remove the protecive blue film from the camera lens.
INNOVATORS OF TECHNOLOGY
2
Dimensions
1
Safety Precauions
Thank you for purchasing a TechNexion AXON series evaluaion kit based on NXP i.MX8M MINI applicaions processor. This installaion guide will be helpful in the
installaion, wiring and inspecion of your TechNexion evaluaion kit. Before using the product, please read this guide to ensure correct use. You should thoroughly
understand all safety precauions before proceeding with the installaion, wiring, and operaion. Place this instrucion sheet in a safe locaion for future reference.
• Keep the device dry. Precipitaion, humidity, and all types of liquids or moisture can contain minerals that will corrode electronic circuits. If your device does get wet,
allow it to dry completely.
• Do not use or store the device in dusty or dirty areas. Its parts and electronic components can be damaged.
• Do not store the device in hot areas. High temperatures can shorten the life of electronic devices, damage bateries, and warp or melt certain plasics.
• Do not store the device in cold areas. When the device returns to its normal temperature, moisture can form inside the device and damage electronic circuit boards.
• This product is designed for specific applicaions and needs to be installed by qualified personnel.
• Do not drop, knock, or shake the device. Rough handling can break internal circuit boards and fine mechanics.
• Do not paint the device. Paint can clog the parts and prevent proper operaion.
• Unauthorized modificaions or atachments could damage the device and may violate regulaions governing radio devices.
• Do not touch any internal or exposed parts of the device as electrical shock may result.
• Do not open the device while power is on. Otherwise electrical shock may result.
• Do not use harsh chemicals, cleaning solvents, or strong detergents to clean the device.
• Be sure the venilaion holes are not obstructed during operaion. Otherwise malfuncion may result due to bad venilaion or overheaing.
These suggesions apply equally to your device, batery, charger, or any enhancement. If any device is not working properly, take it to the nearest authorized service
facility for service.
• Make sure that the available power source matches the required input power of the device. Failure to observe this cauion may result in electric shock or fire.
1.1
Storage and Installaion
1.2
Wiring
1.3
Maintenance and Inspecion
!
Unit : mm
1
2
3
1
2
3
4
5
6
1
2
85
56
1.6
16.41
7.85
3.5
61.5
3.5
52.5
n2.75
1.8
35.8
13.5
33.4