background image

300001749244 Rev A

Page 1

© 2012 Tyco Electronics Corporation. All Rights Reserved.

INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

1

PRODUCT DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2

2

MAIN COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3

3

GROUNDING AND BONDING THE CHASSIS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

4

CHASSIS INSTALLATION PROCEDURE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4

5

DOOR INSTALLATION AND OPERATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

6

WHERE TO FIND OTHER INFORMATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.1

Adapter Pack and Module Installation Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.2

Routing of Cables, Fibers, and Patch Cords. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

6.3

Phone Numbers, Mail Address, Email Address, and Product Portal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

INTRODUCTION

This installation manual describes the NG4access ODF Platform Standard Chassis and provides
all information needed to install this product. This product is intended to be used in a Network
Telecommunication Facilities and is suitable for installation in an Integrated Bonding Network
or a Common Bonding Network.

Content

Page

24939-A

TECP-90-703 

 Issue 1 

 8/2012

NG4access ODF Platform
Standard Chassis

Installation Manual

Summary of Contents for TECP-90-703









Reviews: