background image

MFJ-1792/1793 Instruction Manual

Vertical Antenna

MFJ-1792/1793 Vertical Antenna

Table of Contents:

Introduction ................................................................................................................ 1
Description.................................................................................................................. 1
Bandwidth, SWR, and Power Handling ....................................................................... 2
Choosing a Location for the Antenna........................................................................... 3
Grounding ................................................................................................................... 3
Maintenance ................................................................................................................ 4
Tools and Time Required for Assembly ....................................................................... 4
MFJ-1792 Parts List .................................................................................................... 5
Assembly and Installation Procedure............................................................................ 6
Raising the Antenna..................................................................................................... 11
Tuning the Antenna ..................................................................................................... 12
Technical Assistance.................................................................................................... 13

Summary of Contents for MFJ-1792
















Reviews: