RTR-600BD is the battery charger dock for the RTR-601 Series data loggers. It also acts as a USB
communication interface dock between the RTR-601 and PC for registration and setup of the RTR-601.
• RTR-600BD is referred to as simply the “dock” in this document.
• RTR-601 Series is referred to as simply "RTR-601" or "Remote Unit" in this document.
• To use RTR-601 as a Remote Unit, it is necessary to have any of the compatible Base Units: RTR500BW, RTR-500NW, RTR-500AW, RTR500BC or RTR-500.
Make sure to charge the battery on a flat surface without
vibration. Placing the dock on an unstable surface may result
in injury or damage from falling.
Battery cannot be charged by USB bus power. Make sure to use
the AC adaptor.
To mount the dock on a wall, firmly tighten the screws to
prevent it from falling.
1.
Connect the supplied AC adaptor to the dock.
.
Place the RTR-601 into the dock and charging will begin.
• Once the RTR-601 is recognized, the Blue LED on the dock will light up.
• Once charging begins properly, the Green LED on the RTR-601 will light up
and the LCD display will turn off.
* Up to two Remote Units can be charged
at the same time.
• Once charging has been completed,
LEDs on both the dock and the Remote
Unit(s) will turn off.
Please stop using in the following situations.
• The Red LED on the dock is ON:
If the dock recognizes an irregular electrical activity, it automatically
stops charging and the Red LED will light up. Unplug the AC adaptor
and check the following:
(1) that there are no metallic objects between the dock and Remote
Unit(s), and
(2) if the Remote Unit(s) are properly placed on the dock.
The Red LED on the dock may light up for just a moment due to
power fluctuation. There is no problem unless the Red LED remains
on.
• The Orange LED on RTR-601 is BLINKING:
If the body of the RTR-601 gets too hot (over 40°C), the Orange LED
will start blinking and battery charging will temporarily stop. Once
the body cools down, charging will restart.
• If, after checking the above and resetting the RTR-601 several
times, the Red LED on the dock remains on, please stop using the
dock and contact your distributor.
RTR-600BD Specifications
Compatible
Devices
RTR-601 Series Data Loggers (Remote Unit)
RTR-601-110 / 130 / E10 / E30
Power
AC Adaptor (AD-05A3)
Input Voltage
5V 2A
Communication
Interface
USB / Optical Communication (For Setup)
Charging Method Electromagnetic Induction Type Non-Contact Charg-
ing System
Charging Time
(*1)
Approx. 70 min.
Charging Current 700 mA (typical) per Remote Unit
Dimensions
H 198.3 mm × W 136 mm × D 56.6 mm (including
protrusions)
Weight
Approx. 330 g
Operating
Environment
Temperature: 0 to 40°C
Humidity: 90%RH or less (no condensation)
*1: This is the estimated time to complete a full charge after the battery charge warning
message appears. If the body of the Remote Unit gets hot and battery charging
temporarily stops, the charging time will be longer.
The specifications listed above are subject to change without notice.
For details about registration and settings, refer to
[RT RTR-601 Setup Guide (PDF)] that is available for
download from T&D Website.
tandd.com/manual/
Download and install the software "RTR500BW for Windows"
from T&D Website, and follow the directions as they appear to
complete the registration and setup process.
USB Connection
(2)
(1)
Place the RTR-601 into the right side (with communication
port) of the dock.
Make sure to push down on the RTR-601 until you hear a "click"
sound.
"click"
* Once the registration and setup are complete, make sure to remove the
RTR-601 from the dock to avoid wireless communication failures due to
battery charger noise.
RTR-600BD Part Names
LED (Blue/Red)
LED (Blue/Red)
USB Connector
Remote Unit
Communication Port
AC Adaptor Jack
Accessories Included in Package
• AC Adaptor (AD-05A3)
• USB Cable (US-15C)
• Wall Mount Screws (x 3)
• Manual Set (Warranty Included)
Battery Charge Dock for RTR-601
RTR-600BD User’s Manual
Use as a Battery Charger
Use for Remote Unit Registration
When the [Connect a Remote Unit] dialog box
appears, unplug the USB cable from the Base
Unit (1) and plug it into the dock (2).
Before placing the RTR-601 into the dock, make sure that RTR-601
is not greasy or dirty as the dock is not waterproof and cannot be
washed.
