![background image](http://html1.mh-extra.com/html/system-sensor/m200g-rf/m200g-rf_installation-instructions-manual_1422129001.webp)
D200-303-00
I56-3892-002
Pittway Tecnologica S.r.l. Via Caboto 19/3, 34147 TRIESTE, Italy
DESCRIPTION
The M200G-RF is an advanced RF device designed for use
with addressable intelligent fire systems that use a compatible
proprietary communication protocol for monitoring and control.
The gateway contains a wireless transceiver that enables bi-
directional RF communication between System Sensor radio fire
detection and signalling devices and the CIE controlling the fire
alarm system.
This device conforms to EN54-25, EN54-17 and EN54-18. It
complies with the requirements of 2014/53/EU for conformance
with the RED directive.
SPECIFICATIONS
Comm. Loop Supply Voltage: 15 – 29 V Direct Current (Loop current ≤
900mA)
Max short circuit protection current: 900mA
Comm. Loop Standby Current: @ 24V: up to 510µA max depending on
(no loop communication)
RF configuration (worst case 32 devices
in star configuration
Comm. Loop (poll once per 5s: @ 24V: up to 3.4mA max depending on
green LED blink)
RF configuration (worst case 32 devices
in star configuration
Loop LED on current (max):
Red 4mA, Amber 5.3mA
Power On initialisation time:
2 Secs (typical)
Radio Frequency:
865-870 MHz (up to 18 channels)
RF output power:
14dBm (max)
Range:
400m (typ. in free air)
RF communications with up to 32 RF devices
Relative Humidity:
10% to 93% (non-condensing)
Wiring:
0.75mm
2
– 2.5mm
2
max
The gateway must be powered by a limited power source with Safety Extra
Low Voltage (SELV) and with the required overload and short circuit protections
Gateway Loop Isolator
Isol. max. continuous current (switch closed): 0.9A (input voltage ≤ 29V)
Isolator max. switching current:
0.9A (input voltage ≤ 29V)
Max. isolation current (switch open):
15mA @ 24V
Max. series resistance (switch closed):
300 m ohm
INSTALLATION
This equipment and any associated wiring work must be installed
in accordance with all relevant codes and regulations.
Figures 1 and 2 detail the installation of the B501AP base (further
instructions are available for this if required - see document ref.
D550-33-00).
Note
Spacing between radio system devices must be a
Minimum
of
1m
Anti-Tamper Feature
The base includes a feature that, when activated, prevents removal
of the gateway from the base without the use of a tool. See Figures
3a and 3b for details on this.
SETTING THE ADDRESS
Set the address by turning the two rotary decade switches on the
underside of the gateway (see figure 4 overleaf), using a screwdriver
to rotate the wheels to the desired address. The gateway will take
one module address on the loop. Select a number between 01 and
159 (Note: The number of addresses available will be dependent
on panel capability, check the panel documentation for information
on this). Record the address on the label attached to the base.
Insert the gateway into the base and rotate it clockwise until it locks
into place.
M200G-RF
RADIO SYSTEM GATEWAY
INSTALLATION INSTRUCTIONS
E N G L I S H
102 mm
42 mm
90g
-30°C
60°C
1
2
3
4
-
-
+
+
Figure 2: B501AP Wiring
1
2
3
4
50-60 mm
SHIELD
≤
M4
Figure 1: B501AP Mounting
ADDRESS TAG
B501AP
M200G-RF
COMP
ATIBLE CIE
Figure 3a: Activation of Tamper Resist Feature
PLASTIC LEVER
BREAK TAB AT DOTTED LINE BY
TWISTING TOWARDS CENTRE OF
BASE
Figure 3b: Removing Repeater From Base
USE A SMALL-BLADED SCREWDRIVER TO PUSH
PLASTIC IN THE DIRECTION OF THE ARROW
I 56- 3892- 002