![background image](http://html1.mh-extra.com/html/system-sensor/b501b-ftx/b501b-ftx_installation-and-maintenance-instructions_1422322001.webp)
D200-74-00
1
I56-1195-01R
Before Installing
Please thoroughly read the system wiring and installation
manuals, and manual I56-407,
Guide for Proper Use of
System Smoke Detectors,
which provides detailed informa-
tion on detector spacing, placement, zoning, and special
applications. Copies of these manuals are available at no
charge from System Sensor.
NOTICE:
This manual should be left with the owner/user
of this equipment.
IMPORTANT:
The detector used with these bases must
be tested and maintained regularly following NFPA 72
requirements. The detectors should be cleaned at least
once a year.
Mounting
The detector base mounts directly to 3
1⁄2
- and 4-inch octa-
gon and 4-inch square boxes, with or without a plaster
ring.
To mount, remove the decorative ring by rotating it in either
direction to unhook the snaps. Then, separate the ring from
the base. Install the base on the box, using the screws sup-
plied with the junction box and the appropriate slots in the
base. Replace the decorative ring on the base and rotate it in
either direction until the ring snaps in place (see Figure 1).
Specifications
Base Diameter:
6.1 inches (155 mm)
Base Height
1.2 inches (31 mm)
Mounting:
4-inch square box with or without plaster ring, Min Depth - 1.5 inches (13 mm)
4-inch octagon box, Min. depth - 1.5 inches (13 mm)
3
1/2
-inch octagon box, Min. depth - 1.5 inches (13 mm)
Operating Temperature Range:
0° to 49°C (32° to 120°F)
Operating Humidity Range:
10% to 93% Relative Humidity, noncondensing
Electrical Ratings
Operating Voltage:
15 to 32 VDC
Currents:
Detector–
230µA@24VDC (without communication)
285µA@24VDC (one communication every 5 seconds with LED enabled)
Air Intake–
6mA standby
60mA when checking for smoke (5 seconds on, 30 seconds off)
80mA when checking for proper airflow (15 seconds on, every 4 hours)
Installation Guidelines
All wiring must be installed in compliance with all appli-
cable local codes and any special requirements of the local
authority having jurisdiction, using the proper wire sizes.
The conductors used to connect smoke detectors to control
panels and accessory devices should be color-coded to
reduce the likelihood of wiring errors. Improper connec-
tions can prevent a system from responding properly in the
event of a fire.
For signal wiring (the wiring between interconnected detec-
tors), it is recommended that the wire be no smaller than
18 gauge (1.0 square mm). However, wire sizes up to 12
gauge (3.3 square mm) can be used with the base. The
use of twisted pair wiring or shielded cable for the power
(+ and –) loop is recommended to minimize the effects of
electrical interference.
If shielded cable is used, the shield connection to and from
the detector must be continuous by using wire nuts, crimp-
ing, or soldering, as appropriate, for a reliable connection.
Alarm system control panels have specifications for allow-
able loop resistance. Consult the control panel specifica-
tions for the total loop resistance allowed before wiring
the detector loops.
B501B-FTX Detector Base
For use with the Filtrex™ Smoke Detector
INSTALLATION AND MAINTENANCE INSTRUCTIONS
3825 Ohio Avenue , St. Charles, Illinois 60174
1-800-SENSOR2, FAX: 630-377-6495
www.systemsensor.com
D200-74-00
4
I56-1195-01R
©2001 System Sensor
Three-Year Limited Warranty
System Sensor warrants its enclosed smoke detector base to be free from
defects in materials and workmanship under normal use and service for a
period of three years from date of manufacture. System Sensor makes no
other express warranty for this smoke detector base. No agent, represen-
tative, dealer, or employee of the Company has the authority to increase
or alter the obligations or limitations of this Warranty. The Company’s
obligation of this Warranty shall be limited to the repair or replacement
of any part of the smoke detector base which is found to be defective in
materials or workmanship under normal use and service during the three
year period commencing with the date of manufacture. After phoning
System Sensor’s toll free number 800-SENSOR2 (736-7672) for a Return
Authorization number, send defective units postage prepaid to: System
Sensor, Repair Department, RA #__________, 3825 Ohio Avenue, St.
Charles, IL 60174. Please include a note describing the malfunction and
suspected cause of failure. The Company shall not be obligated to repair
or replace units which are found to be defective because of damage,
unreasonable use, modifications, or alterations occurring after the date
of manufacture. In no case shall the Company be liable for any conse-
quential or incidental damages for breach of this or any other Warranty,
expressed or implied whatsoever, even if the loss or damage is caused by
the Company’s negligence or fault. Some states do not allow the exclu-
sion or limitation of incidental or consequential damages, so the above
limitation or exclusion may not apply to you. This Warranty gives you
specific legal rights, and you may also have other rights which vary from
state to state.
Please refer to insert for the Limitations of Fire Alarm Systems
I56-1
195-01R