SuperDroid Robots IG52 DB Скачать руководство пользователя | Manualshive

Страница: 1 / 12

background image

Mecanum Wheel Vectoring Robot - IG52 DB

Assembly and Operation

This is a chain drive 4WD base Programmable robot kit that uses 8" Nexus mecanum wheels

allowing it to vector in any direction. It can support payloads up to 200 lbs. Make it RC or use it with

sensors and a microcontroller to make it autonomous/semi-autonomous.

Images shown may not be an exact representation of the robot’s

features listed in this document

1
2
3
...
»

Содержание IG52 DB













Отзывы:

Нет отзывов

Похожие инструкции для IG52 DB

Бренд: Kettler Страницы: 17

MOTOMAN-MPL80 II

Бренд: YASKAWA Страницы: 81

Бренд: YASKAWA Страницы: 92

Sten-Bot Robot Kit

Бренд: Stensat Страницы: 73

Obstacle Avoidance Smart Car Kit

Бренд: LAFVIN Страницы: 80

Robo 2.0 Ninja Sword

Бренд: Artec Страницы: 10

Бренд: MD SPORTS Страницы: 17

Sabertooth 2X25

Бренд: Dimension Engineering Страницы: 2

Line Follower Robot Racing

Бренд: COLMAC Страницы: 55

Бренд: Blue Robotics Страницы: 17

MICRONOID CODE MAGNA

Бренд: Meccano Страницы: 32

Бренд: Kondo Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды