background image

 

 

1

Owner’s Manual 

Stainless Steel Patio Heater —L-PH011PSS-2 

 

 

 

 

 

 

 

Propane tank not included 
1 AAA battery included 

 

 

 

 

 

Standard: ANSI Z83.26a-2008/CSA 2.37a-2008, Gas-Fired Outdoor Infrared Patio Heater  

 

Questions, problems, missing parts? Before returning to your retailer, call our customer service 

department at 1(866) 578-6569 from 8:30 AM to 5:30 PM EST , Monday-Friday .

 

Warning: For Outdoor Use Only 

Warning: For your safety 

Chemical known to the State Of California to cause 

cancer, birth defects, or other reproductive harm 

are created by the Combustion of Propane. 

 

Warning: For your safety.   

If you smell gas: 

1.  Shut off gas to the appliance.   

2.  Extinguish any open flame. 

3. If odor continues, immediately call your gas 

supplier or local fire department.

 

Warning: For your safety 

Failure to follow the manual’s warning and 

instructions can result in severe personal injury, 

death, or property damage. 

Warning: For your safety 

Improper installation, adjustment, alteration, 

services or maintenance can cause injury or 

property damage. Read the installation, operation 

and maintenance instructions thoroughly before 

installing, operating or servicing this equipment. 

Warning: 

Do not store or use gasoline or   

other flammable Vapors and liquids in the vicinity   

of this or any other appliance. 

An LP-cylinder not connected for use shall not be 

stored in the vicinity of this or any other appliance. 

 

Summary of Contents for L-PH011PSS-2














Reviews: