1
Full Press: When fully pressed, you will hear a clicking sound.
Revised: 10-22-2014
SWPFTB10R
Instruction Manual
STOP.
Before Proceeding, Please Read:
This stun baton flashlight performs many functions and has built in safety features that can be
confusing if you do not take time to read these directions and familiarize yourself with it. The key to understanding how this unit operates is the
“Function-Select Button.” Each time this button is pressed, the function changes in the following order: Light, Stun, Off. To help you remember the
order, the corresponding symbol is shown below the Function-Select Button:
for Light,
for stun, and
for off.
Inserting and Charging the Rechargeable Batteries
1.
We recommend fully charging the rechargeable batteries before inserting them into the unit. To do so, insert both 18650 4000mAh 3.7V li-ion batteries
(included) into the charging port according to the polarity diagram shown on the port. If the batteries are inserted correctly a red light will illuminate on the
charging port. Next, plug
the slide-out plug into a standard wall outlet. When plugged into a standard wall outlet, a red light on the wall charger will come
on while the batteries are charging and change to green when completely charged.
IMPORTANT:
Do not charge for more than 8 hours at a time.
Overcharging can damage the batteries and void the warranty. If the flashlight becomes dim or if the electrical stun current becomes noticeably weaker,
the batteries will need to be charged. When not in use, charge the batteries every 60 days to ensure the unit will function optimally when needed.
2.
To insert the batteries into the stun baton, unscrew the end cap by turning it in a counterclockwise direction (See above diagram for location to unscrew).
3.
Insert the batteries according to the polarity diagram below.
IMPORTANT
: Batteries must be inserted as shown below. Inserting the batteries incorrectly
could damage the unit and void the warranty. Replace the end cap by turning in a clockwise direction until snug. Do not over tighten.
Using the Flashlight
Overview: This unit features three (3) light strengths (Maximum, Medium, & Low) and two light patters (SOS
& Strobe). When the situation does not require
maximum light strength, the lower light settings can be used to extend the battery life.
1.
Be sure the unit is set to Light Function (remember there are three (3) functions in the following order: Light, Stun, & Off)
2.
Press the Function-Select Button until you see the light turn on. Note: If you press it more than three times and still do not see the light, fully press
1
the
Push-Button Tail Switch. In the Light function, this button will turn the light on and off (full press
1
) or change the light mode (half press).
3.
Once the light is on you can change the light mode by either half pressing
either
the Function-Select Button or the Push-Button Tail Switch.
4.
To turn off the light, fully press
1
either
the Function-Select Button or the Push-Button Tail Switch.
5.
If you turn the light off by fully pressing
1
the Push-Button Tail Switch, you will need to press this same button again to turn it on. If you turn it off by fully
pressing
1
the Function-Select Button be careful to note that you are now in stun function and pressing the Stun Activation Button will activate the stun
feature. To return to light function, you will need to press the Function-Select Button two (2) more times. Remember the order of the functions: When set to
Light Function, pressing once moves the function to Stun, pressing twice moves it to Off and pressing a third time moves it back to Light.
Testing
the Stun Baton
(
WARNING:
Do not test fire the stun baton for more than 1 second as this will damage the unit and void the warranty.)
1.
First, you need to be sure the unit is set to Stun Function (Remember there are three functions- Light, Stun, & Off)
2.
The easiest way to locate the Stun Function is to fully press
1
the Function-Select Button until you see the light turn on. Note: If you press it more than three
(3) times and still do not see the light, fully press
1
the Push-Button Tail Switch. Remember, if this button was pressed, the safety is ON and all of the
features are disabled until this button is pressed again.
3.
Once the light is on, press the Function-Select Button once more. The unit is now in Stun Function.
CREE LED Flashlight
Triple Stun
Contact Probes
Stun Activation Button
Function-Select Button
(Light, Stun, Off)
Push-Button Tail Switch (Not Shown):
o
Full Press
1
turns unit On/Off.
o
Half Press changes light mode.
Unscrew Here to
Insert Batteries
Negative ( - )
Positive ( + )
End Cap
